Valve stem seals - easy enough?
Discussion
I think my left hand bank has a bit of an oil consumption problem and i'm 90% sure it's not rings so i'm guessing it's valve stem seals.
Since this is a pretty simple 16 valve, single cam, pushrod engine i'm guessing that changing the valve stem seals should be a doddle, right?
Pop the plenum out the way, undo the plug leads, pop the rocker cover off, take the rocker arm off, and then get the old valve spring compressor out and get to work right?
Last time i did this was an ex-girlriends OHV Fiesta, same thing right?
Or am i over simplifying?
Since this is a pretty simple 16 valve, single cam, pushrod engine i'm guessing that changing the valve stem seals should be a doddle, right?
Pop the plenum out the way, undo the plug leads, pop the rocker cover off, take the rocker arm off, and then get the old valve spring compressor out and get to work right?
Last time i did this was an ex-girlriends OHV Fiesta, same thing right?
Or am i over simplifying?

Ah, just found this: http://www.pistonheads.com/gassing/topic.asp?h=0&a...
I think the biggest dilemma is that when you get the springs off, you won't like the look of the gouging in the spring seats. Unless you are really in a rush, popping the heads off so you can clean, lap .. have the spring seats reground and steel shims put in.. is the way I would approach it. I reckon its the price you have to pay with the cams & uprated valve springs?
Well, having look at that other thread i think what i'll do is go and compression test the engine.
If it's even across all the cylinders then i'll just replace the valve stem seals for now and see how i get on, i can always take the heads off next winter.
If the compression is crap then i'll have to decide if i should fix it myself or just give it to someone else to do (which will be quicker and save me taking time off work).
If it's even across all the cylinders then i'll just replace the valve stem seals for now and see how i get on, i can always take the heads off next winter.
If the compression is crap then i'll have to decide if i should fix it myself or just give it to someone else to do (which will be quicker and save me taking time off work).
Not a great picture (and its not all swarf) but should give you an idea of the wear to expect on the spring seats. These were not bad ones either from what I've seen?
http://foo.dspen.com/springseat.jpg
http://foo.dspen.com/springseat.jpg
VerySideways said:
Pop the plenum out the way, undo the plug leads, pop the rocker cover off, take the rocker arm off, and then get the old valve spring compressor out and get to work right?
Pretty much, assuming you have a valve spring compressor that can compress the spring in situ. Obviously you'll need something to hold the valve up, I use the 'rope' trick but others use an air line into the plug hole. Access to the back of the engine is going to be a bit awkward because the bodywork comes so far forward, but apart from that it's straight forward.Try using this link
http://landrover-online.dk/L-R%20WSM/engine/V8over...
or the v8developements web site
Trev
http://landrover-online.dk/L-R%20WSM/engine/V8over...
or the v8developements web site
Trev
Never had any issue with the spring seats on mine; I'm wondering if that's more of an issue if the springs are very tired and perhaps moving around at higher rpm.
Access to the rear ones is very tight, in fact it's marginal and a right faff (but do-able). Thing that caused me most concern was on rebuilding/restarting, I had quite a lot of valve noise and the wisdom of those I asked seemed to be along the lines the lifters had probably over-pumped. Given they are not easily (if at all) bled down in situ, and I was looking at a potential strip down anyway, I just took it out and caned it... all quiet again. Probably not the approved method
Access to the rear ones is very tight, in fact it's marginal and a right faff (but do-able). Thing that caused me most concern was on rebuilding/restarting, I had quite a lot of valve noise and the wisdom of those I asked seemed to be along the lines the lifters had probably over-pumped. Given they are not easily (if at all) bled down in situ, and I was looking at a potential strip down anyway, I just took it out and caned it... all quiet again. Probably not the approved method

Had my stem seals done last year as the car was smoking like mad for a short while after starting from a 2 week or so lack of use.
I am no mechanic so got Fernies to do the whole thing and they reground the valves and had the chance to give both heads a good look over after 60k miles - no further problems and IIRC the whole thing including the service was around £1500.
I am no mechanic so got Fernies to do the whole thing and they reground the valves and had the chance to give both heads a good look over after 60k miles - no further problems and IIRC the whole thing including the service was around £1500.
I would have thought its more likely to be down to the cam profile & rev ranges.. the TVR dual springs seem pretty durable from what I've measured (certainly compared to the mishmash you get with std Rover springs - yes I've stripped a few for bits and compared out of purile interest
).
). Well, did the left hand bank - couldn't get the air adapter thingy on to the back two plug holes very well which made it nerve wracking but apart from that it was good.
Plug on cylinder 3 (second one from the front on the left hand bank) was absolutely caked, and one of the valve stem seals on that cylinder was oval. OVAL!
New plug, new valve stem seals, car runs like a dream
Thanks for everyone's help on this thread, i will get some nylon rope before i do the other bank, just in case.
Plug on cylinder 3 (second one from the front on the left hand bank) was absolutely caked, and one of the valve stem seals on that cylinder was oval. OVAL!
New plug, new valve stem seals, car runs like a dream

Thanks for everyone's help on this thread, i will get some nylon rope before i do the other bank, just in case.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





