Does this sound ok
Does this sound ok
Author
Discussion

pinchmeimdreamin

Original Poster:

10,917 posts

249 months

Sunday 22nd February 2009
quotequote all
Got the chim out from her winter layup a couple of weeks ago and maybe im being a bit paranoid but theres a bit of a tapping/knocking coming from drivers side of the engine (replaced manifold gaskets with steel ones and arp bolts end of last year).

This may not help but would appreciate if you guys would have a quick listen (apologies for crap videoing laugh and yes i know the engine needs a clean rolleyes )

Any advice appreciated
http://www.onetruemedia.com/shared?p=820e4ed68387c...


Barkychoc

7,848 posts

235 months

Sunday 22nd February 2009
quotequote all
I'd say thats a blowing exhaust - new gaskets or not.
Try listening with a piece of hose.

bobfather

11,197 posts

286 months

Sunday 22nd February 2009
quotequote all
Sounds like you may have a common failure. The four into one joint at the pre-cats is a known failure point especially after the manifold has been disturbed. The failure tends to occur in the middle of the four pipes so it isn't economic to repair.

bobfather

11,197 posts

286 months

Sunday 22nd February 2009
quotequote all
This is my method for detecting a leak

Link

aka tvrbob

Barkychoc

7,848 posts

235 months

Sunday 22nd February 2009
quotequote all
Darren I see you are in Nottingham.

On the basis that if it is in the middle of the four pipes as above I'll happily have a bash at welding it if you want working on the basis that it may not be repairable and I could make it worse if the metal is like a kit kat wrapper. You have to cut the end off the manifold, weld it up inside then weld the end of the manifold back on.

One of mine has been done successfully before.

I'm in Bingham by the way.

Chris

PS you'll have to remove the manifold and bring it to me!


Edited by Barkychoc on Sunday 22 February 16:43

pinchmeimdreamin

Original Poster:

10,917 posts

249 months

Sunday 22nd February 2009
quotequote all
Thanks for the speedy replies guys, will try to get some bungs and do the Bob test yes
Anyone know what size bung off the top of there head?


Barkychoc thanks for the offer if it does end up being the 4 into 1 i may take you up on the offer.

Or i may just use it as an excuse to get a nice shiny ACT manifold laugh

Edited by pinchmeimdreamin on Sunday 22 February 16:50

daz the plumber

14,997 posts

262 months

Sunday 22nd February 2009
quotequote all
hi, i had my manifolds off three times , on inspection they were slightly warped.i went to linleys engineering in nottingham to have the faces skimmed, they have been on for a year with out a problem .i used a scethoscope.

Edited by daz the plumber on Sunday 22 February 17:16

Barkychoc

7,848 posts

235 months

Sunday 22nd February 2009
quotequote all
pinchmeimdreamin said:
Thanks for the speedy replies guys, will try to get some bungs and do the Bob test yes
Anyone know what size bung off the top of there head?


Barkychoc thanks for the offer if it does end up being the 4 into 1 i may take you up on the offer.

Or i may just use it as an excuse to get a nice shiny ACT manifold laugh
You could get someone to hold rags over the exhausts assuming you have some friends hehe

pinchmeimdreamin

Original Poster:

10,917 posts

249 months

Sunday 22nd February 2009
quotequote all
Well just ordered a stethoscope off fleabay so will try and see if i can figure out where the leak is when that arrives then go from there, at least if i have to get the manifolds off again I know how to do it and have the bent spanners ready.

Badmutha

658 posts

224 months

Sunday 22nd February 2009
quotequote all
[quote=pinchmeimdreamin]Thanks for the speedy replies guys, will try to get some bungs and do the Bob test yes
Anyone know what size bung off the top of there head?


Tennis balls should do it

slideways

4,101 posts

252 months

Sunday 22nd February 2009
quotequote all
check your arp bolts are still tight mine come loose regularly as i havnt fitted my nordlock washers yet
Rich

pwd95

8,459 posts

269 months

Sunday 22nd February 2009
quotequote all
Could be a lazy lifter. Tighten the manifolds up, take it for a dam good thrashing, do an engine flush oil change (put engine flush in & hold it at 2k rpm for 20 mins), take it for another dammmm goood thashshshshing. See how she sounds. yes

Cured my lazy lifter. yes

Edited by pwd95 on Sunday 22 February 23:36