Fault Code 46
Fault Code 46
Author
Discussion

V8 Animal

Original Poster:

6,015 posts

241 months

Sunday 1st March 2009
quotequote all
I was putting the car away last night and caught sight of my fault reader showing 46
Which is a lamda sensor nearside out of range.
After running out of fuel a week ago only got 205 miles out of tank which i know is not right have been getting near 300
Adjusted AFM now tanks about empty and 230 miles and i had adjusted it with about half a tank so i reckon im on the right side.
Has this affected the lambda or is it shot?
I suppose i could reset it and monitor it just after some views.
Cheers

scotty_d

6,795 posts

225 months

Sunday 1st March 2009
quotequote all
How do you adjust your AFM mine is only getting around 200 ish to a tank but i have the same fault code due to the lamda's not having there 12v due to the wrong realy being fitted to the fuel pump it was overfueling very badly only getting 150 out a tank. i did not get a chance to set it all up last summer so this could help me too. its going to get looked at on wednesday anyway but this could help.

Cheers Scotty



Edited by scotty_d on Sunday 1st March 10:46

V8 Animal

Original Poster:

6,015 posts

241 months

Sunday 1st March 2009
quotequote all
scotty_d said:
How do you adjust your AFM mine is only getting around 200 ish to a tank but i have the same fault code due to the lamda's not having there 12v due to the wrong realy being fitted to the fuel pump it was overfueling very badly only getting 150 out a tank. i did not get a chance to set it all up last summer so this could help me too. its going to get looked at on wednesday anyway but this could help.

Cheers Scotty



Edited by scotty_d on Sunday 1st March 10:46
You need a multimeter and i used a paperclip pushed down the wire far left and far right wires to get a reading on the meter probes.
You should have a slot on the right hand side of the meter looking down on it and i used a wide flat screwdriver to adjust to 1.8v for a cat car ignition on but engine not running.
Has a significant difference to the fueling.
Do a search for more info a lot on here.

lewis_sharman

5,958 posts

222 months

Sunday 1st March 2009
quotequote all
I am only getting about 150 miles to a tank also. What would be the list and order of things to check?

blitzracing

6,422 posts

251 months

Sunday 1st March 2009
quotequote all
I dont have 46 as a 14CUX code, only 44 and 45, but anyway its easily found if it is lambda out of Range. Firstly, check the plug colours on both sides. If one side is darker then the other, then you know which side has failed (Im assuming its running rich). The ECU will flag Lambda out of range if the probe stops switching, so get the car warm, and put a test meter across the white and black connections to the probe (you can try the socket by the probes or the extensions behind the fuel rail). It should be switching between about .2 and .8 volts dc at tickover at about 1/2 -3/4 second intervals (This is never that precise). I suspect you will find one side either stuck low, or possibly high (although this will be indicating a severe overfueling issue). Its most likely a probe has failed (low or no output) and the ECU is putting in too much fuel as it has no feedback. Also If you have fault code the ECU is likely to be in get you home mode, and the fuel economy will suffer. If you need a probe, dont buy them in this country they are silly money. You can get them from the USA (Ebay) for a lot less.

http://stores.ebay.com/GLOBAL-AUTOMOTIVE

Mak


V8 Animal

Original Poster:

6,015 posts

241 months

Sunday 1st March 2009
quotequote all
blitzracing said:
I dont have 46 as a 14CUX code, only 44 and 45, but anyway its easily found if it is lambda out of Range. Firstly, check the plug colours on both sides. If one side is darker then the other, then you know which side has failed (Im assuming its running rich). The ECU will flag Lambda out of range if the probe stops switching, so get the car warm, and put a test meter across the white and black connections to the probe (you can try the socket by the probes or the extensions behind the fuel rail). It should be switching between about .2 and .8 volts dc at tickover at about 1/2 -3/4 second intervals (This is never that precise). I suspect you will find one side either stuck low, or possibly high (although this will be indicating a severe overfueling issue). Its most likely a probe has failed (low or no output) and the ECU is putting in too much fuel as it has no feedback. Also If you have fault code the ECU is likely to be in get you home mode, and the fuel economy will suffer. If you need a probe, dont buy them in this country they are silly money. You can get them from the USA (Ebay) for a lot less.

http://stores.ebay.com/GLOBAL-AUTOMOTIVE

Mak
Err typo sorry mark 45 which is the nearside.
Luckly managed to buy one for £30 of ebay new.
Deffo not in limp home mode the beanz i was giving it before i put her away to cool down.
That Scooby ain't having me lollaughthe wife new straight away what we racing errangel