ACT Induction kit
Discussion
Got the car booked up for a dyno run on 23rd of this month (mainly to check to see how it is doing after 100,000 miles), so i thought it would be a good idea to do a full 12,000 mile service on it myself to make sure everything is tip top.
This is where my *money saving* stupidity has come in.
Somehow, while looking for replacement air filters i have managed to worm myself onto the ACT website and order a full smooth bore induction kit from them.
I am so weak

Is there anything else i should be checking?
This is where my *money saving* stupidity has come in.
Somehow, while looking for replacement air filters i have managed to worm myself onto the ACT website and order a full smooth bore induction kit from them.
I am so weak


Is there anything else i should be checking?
at that kind of mileage (the car looks fantastic by the way)... I'd consider over anda bove the service book requirements at looking at getting the injectors cleaned/replaced.... check the cam for wear as well..... but evrything else should be fine provided serviced regulary... airfilter is generaly the biggest over looked though due to access requirements
Don't beat yourself up over that ACT kit - it's worth about an extra 10 BHP, especially with the smooth right angle pipe - You bought well!
If it was me, I'd have thrown the ACT carbon fibre trumpet set in the basket while I was there too!
I'd take a look at Oil filer, Fuel filter (tough job), Air filter, brake pads and fluids (PAS, Hydraulic etc)
If it was me, I'd have thrown the ACT carbon fibre trumpet set in the basket while I was there too!

I'd take a look at Oil filer, Fuel filter (tough job), Air filter, brake pads and fluids (PAS, Hydraulic etc)
lewis_sharman said:
Got the car booked up for a dyno run on 23rd of this month (mainly to check to see how it is doing after 100,000 miles)
Full power dyno runs can be rather hard on the engine, are you sure that it's (a) going to tell you anything useful and (b) something you really want to be putting a tired engine through?Thanks for all the info, i was planning on going through all fluids and filters along with brakes aswell, but had neglected to think of the injectors. Is there anywhere around the south east that anyone would recommend for cleaning?
And i have full confidence in the fact that its still in good health in the time that i have had it.
Worst case scenario = Good excuse to get a 4.6
And i have full confidence in the fact that its still in good health in the time that i have had it.
Worst case scenario = Good excuse to get a 4.6

Barreti said:
You'll possibly need to cut them though. Remember, measure twice / cut once.
The 90deg is easy to get right, the one connected to the air filter is a bit more difficult.
I've found a hacksaw is good on Silicone hoses - I know, but it is, honestly.
The ACT hoses don't look silicone, they're more a rubbery (Japanese for lovely?) texture and as such probably don't suffer from "furry edge" problems that you get when chopping normal silicone hoses with something like a hacksaw, so on that basis I would argue a hacksaw is probably quite a good tool to use, confirm with ACT if unsure though. It would be possible to have different pipes made in different lengths, but I know that my own silicone hose moulds cost 300 pounds each to make and I have 4 of them just for my cerb induction kits, that's a lot of investment to get back before you turn a profit .. so making them slightly oversize and cutting down to suit is by far the best option. Hacksaw away The 90deg is easy to get right, the one connected to the air filter is a bit more difficult.
I've found a hacksaw is good on Silicone hoses - I know, but it is, honestly.
The 90 deg bend is proven certainly to be a significant hp improver even on std cars. Much neater job is acheived if you use a fresh stanley bladed knife and use the hose clips as your hard edge then cut around the hose,use the supplied stainless steel joiner in the kit to keep the end your cutting round when your doing this(stop hose deforming collapsing)the rubber hose that ACT supply cuts a treat using this method,remember as already suggested measure twice cut once 

Gassing Station | Chimaera | Top of Page | What's New | My Stuff




