Boot release switch with ignition off ?
Discussion
I know that there are kits out there to remotely open the boot, but i will be happy if i dont have to keep turning the ignition on to open the boot all the time.
I am thinking of changing the ignition wire on the boot release switch, to a permanent live with an inline fuse does anyone know if that will work?
I am thinking of changing the ignition wire on the boot release switch, to a permanent live with an inline fuse does anyone know if that will work? I fitted a push type switch in the O/S (B pillar?), at the top, in the carpet, you can hardly see it.
It is wired up using a cheapo 4 pin relay to the door switch in such a way that it only works when the driver's door is open.
When the car is parked with the roof off the switch won't work, job done.
It is wired up using a cheapo 4 pin relay to the door switch in such a way that it only works when the driver's door is open.
When the car is parked with the roof off the switch won't work, job done.
I have done a mod to mine with a aluminum push button on the right corner of the dash. This works only when the car is unlocked. The easy way to get the feed for this was to put a microswitch on the door lock mechanism. The door lock mechanism has a solenoid which locks/unlocks the door. The microswitch then switches a live feed to the boot release button when unlocked. Cost £20 and took a few hours.


Ribol said:
^^^^ any excuse to show the carbon fibre off 

Is it that obvious? 
Forgot to say that the boot release mod made a huge difference to the convenience of opening the boot. Got really fed up having to keep key in the ignition position and pushing the button underneath the console.
Chimjunkie said:
Ribol said:
^^^^ any excuse to show the carbon fibre off 

Is it that obvious? 
Forgot to say that the boot release mod made a huge difference to the convenience of opening the boot. Got really fed up having to keep key in the ignition position and pushing the button underneath the console.

Chimjunkie said:
Ribol said:
My relatively low tech (read cheap) method has also made life easier........but isn't enhanced by posting any photos 


Have you made an excuse yet for not putting your name down on the Herts and Beds run-in list? Would be great to have you along...

Ribol said:
Chimjunkie said:
Ribol said:
My relatively low tech (read cheap) method has also made life easier........but isn't enhanced by posting any photos 


Have you made an excuse yet for not putting your name down on the Herts and Beds run-in list? Would be great to have you along...


Wasn't the hold door button release attributed to Henley ?
Theres a nice power supply from the hoop courtesy light, and the loom to the release near the petrol filler. A bit of wire and any simple button in that area should do the job, at least you only have to reach in from the right corner or passenger door then.
You still have the shame of having to walk back around the car if you forget Jon

Theres a nice power supply from the hoop courtesy light, and the loom to the release near the petrol filler. A bit of wire and any simple button in that area should do the job, at least you only have to reach in from the right corner or passenger door then.
You still have the shame of having to walk back around the car if you forget Jon


Bluebottle said:
If you have an aftermarket alarm system fitted, you can get the boot release solenoid connected into the alarm. Which what I had done, so I can open the boot from my key fob.
I've got an after market Laserline alarm fitted. I only have the operators manual, not the installation one, but I guess it would be simple to find where the boot open signal outputs from. The only thing is where to connect this to. Does the standard car switch operate the solenoid directly or does it operate a relay? If so, where is it?Has anyone had this done, as I think it would be a great mod.
Thanks
D
Gassing Station | Chimaera | Top of Page | What's New | My Stuff






Thanks everyone for your advice, some good alternatives