Ignition parts quality
Ignition parts quality
Author
Discussion

taylormj4

Original Poster:

1,635 posts

297 months

Friday 13th March 2009
quotequote all
Is it really worth paying the extra for a Lucas Distributor cap and rotor arm. What is so much better about them. They are seemingly pretty basic components.

Matt

steve-V8s

2,924 posts

279 months

Friday 13th March 2009
quotequote all
Yes, certainly the cap, not so sure about the rotor. I went to the local landy dealer thinking they would have original or at leats good ones but it fell apart in no time, took it back and turns out it was a pattern part. No surprise they fall apart when you look closely at how it is moulded, especially around the contacts. The other concern I had with the pattern parts that were stocked most places I tried was the plastic, it seemed very hard and brittle so bits of it break off and disappear into the dizzy. The genuine ones appear to be a softer plastic.

dogbucket

1,256 posts

232 months

Friday 13th March 2009
quotequote all
you can get proper Lucas bits at a good price from http://www.famousfour.co.uk/

That Daddy

19,464 posts

252 months

Friday 13th March 2009
quotequote all
dogbucket said:
you can get proper Lucas bits at a good price from http://www.famousfour.co.uk/
Seconded,good guys.

blitzracing

6,422 posts

251 months

Saturday 14th March 2009
quotequote all
After market Rotor arms can cause all sorts of misfires. Took me ages to find after fitting new parts during a service, and to this day I dont know how a rotor arm can fail like this !

Edited by blitzracing on Saturday 14th March 18:48

That Daddy

19,464 posts

252 months

Saturday 14th March 2009
quotequote all
So good he said it twice hehe HI Mark byebye i have known other car manufacturers to be picky with pattern ignition components Japanese cars in the eighties were especially prone,Toyota,Nissan etc,more the fact that the pattern stuff was crap really rather than the cars being particular,when i was at a Honda dealership we had big problems when some of the older models were fitted with pattern rotor arms(not by us obviously)but that included clutches too,thing is if you look at the Lucas arm its really nothing special just that the pattern arm for the RV8 motor is so sub standard rolleyes the caps i have seen have seemed OK though.

Edited by That Daddy on Saturday 14th March 12:23

Cider Andy

1,889 posts

256 months

Monday 16th March 2009
quotequote all
I wouldn't be too concerned about pattern distributor caps, if the two varieties I've seen are anything to go by, but the rotor arm is a different story. I had a similar problem to blitzracing. The rotor arm appeared to be in excellent condition and had identical dimensions to the original Lucas. But what started out as a misfire culminated in the engine not firing at all. What I discovered was that the spark was passing through the rotor arm itself and grounding via the rotor, hence no spark at the distributor cap electrodes. Simple enough to diagnose once it had failed completely but not so simple whilst it was intermittent.

taylormj4

Original Poster:

1,635 posts

297 months

Monday 16th March 2009
quotequote all
Ok. I need to change my distributor cap as the lead from the coil must have had a bad joint or something and pretty much vaporised the metal end over a period of time, which also caused damage to the socket in the middle of the distributor cap. I have cleaned it out and made up a new lead and engine runs but I suspect it's not a brilliant repair, especially as I have the shunting problem.

Presume if you change the cap you should change the rotor arm at the same time. Thanks for the famous four link - I used to use them for my Range Rover parts but have avoided them with the TVR as people always say "it's not a Land Rover" and you shouldn't buy parts from them.