Aaargh .... £6,000 engine rebuild
Discussion
Hi all - I have some difficult choices to make
My Chimaera 450 melted its cam bearings, and Paul at Austec tells me there is not a lot that doesn't need doing. £6,000 gets me a rebuilt, balanced, effectively blueprinted engine.
Now I have no doubt that Paul and crew will do a first class job, but I had already decided to sell the car after nearly 5 years. If I was keeping it, then I would get the benefits but right now the considerations are purely commercial. So do I
1) try to sell in present state to someone who wants a project
2) Pay up and sell a great car with a fresh engine
3) Look for a cheaper replacement engine
It's a 1999 car with sound chassis and first class bodywork and Intrax suspension
My Chimaera 450 melted its cam bearings, and Paul at Austec tells me there is not a lot that doesn't need doing. £6,000 gets me a rebuilt, balanced, effectively blueprinted engine.
Now I have no doubt that Paul and crew will do a first class job, but I had already decided to sell the car after nearly 5 years. If I was keeping it, then I would get the benefits but right now the considerations are purely commercial. So do I
1) try to sell in present state to someone who wants a project
2) Pay up and sell a great car with a fresh engine
3) Look for a cheaper replacement engine
It's a 1999 car with sound chassis and first class bodywork and Intrax suspension
Two really good options for you are;
http://www.v8developments.co.uk/
http://www.rover-v8.com/
They're both RV8 gurus
HTH
http://www.v8developments.co.uk/
http://www.rover-v8.com/
They're both RV8 gurus
HTH
Thanks guys - am finding out much more than I knew a few hours ago. Spoke to Chris at RPi Engineering http://www.v8engines.com/index.html and a short engine seems to be the way to go.
Other links - will check ou - much appreciated
Cheers
Richard
Other links - will check ou - much appreciated
Cheers
Richard
rbryant said:
Thanks guys - am finding out much more than I knew a few hours ago. Spoke to Chris at RPi Engineering http://www.v8engines.com/index.html and a short engine seems to be the way to go.
Other links - will check ou - much appreciated
Cheers
Richard
If you want a short engine, I'd buy one 200 times out of 100 from V8D instead of RIP Other links - will check ou - much appreciated
Cheers
Richard

ETA: typo gets round N&S rather nicely
(thats 'nicely' used in its truest sense
)Edited by spend on Tuesday 17th March 14:39
V8D wont try & sell you an 'improved' ignition amplifier 
Just call V8D, there won't be any bulls
t round there either, they've just ploughed the fields
Whether its Ray, Rob or Shaun who answers they are all top guys and care about what they do.
I'd go as far to say if you just want an engine swap - trailer the car up to them they'll have it in out with no fuss. TBH I don't even bother to ask them prices even & I'm always pleasantly surprised when they ask for money - how many people do you trust like that these days?

Just call V8D, there won't be any bulls
t round there either, they've just ploughed the fields
Whether its Ray, Rob or Shaun who answers they are all top guys and care about what they do.I'd go as far to say if you just want an engine swap - trailer the car up to them they'll have it in out with no fuss. TBH I don't even bother to ask them prices even & I'm always pleasantly surprised when they ask for money - how many people do you trust like that these days?
Not knocking Austec because I'm sure they'll do a cracking job but you could get this done cheaper if you needed to.
I had a full engine rebuild for exactly the same issue (cracked cam bearings) with balanced and polished crank and pistons, lightened flywheel, big end and cam bearings, new rings and hone block, rockers, timing gear, cam kit, head stud kit, adjustable pushrods, engine mounts, fuel hoses, oil seals, rocker covers, all gaskets, silicon hose kit, silicon heater pipes, test and clean injectors, acid dip cylinder head, grind valve seats, steam and pressure test block, 1 year warranty AND 12,000 mile service for significantly less than that.
Once the block is out which it will need to be if it's the rear bearing affected (needs pressing in) then the actual 'blueprinting' bit is next to nothing cost wise so it's a must in my opinion.
And yes I am very happy with my engine!
Pm me for details mr Bryant if you like.
I had a full engine rebuild for exactly the same issue (cracked cam bearings) with balanced and polished crank and pistons, lightened flywheel, big end and cam bearings, new rings and hone block, rockers, timing gear, cam kit, head stud kit, adjustable pushrods, engine mounts, fuel hoses, oil seals, rocker covers, all gaskets, silicon hose kit, silicon heater pipes, test and clean injectors, acid dip cylinder head, grind valve seats, steam and pressure test block, 1 year warranty AND 12,000 mile service for significantly less than that.
Once the block is out which it will need to be if it's the rear bearing affected (needs pressing in) then the actual 'blueprinting' bit is next to nothing cost wise so it's a must in my opinion.
And yes I am very happy with my engine!

Pm me for details mr Bryant if you like.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





I took the engine away from the "specialist" & sent it to the people who know what they are doing 
