stepper motor
stepper motor
Author
Discussion

dc400

Original Poster:

125 posts

237 months

Wednesday 18th March 2009
quotequote all
my stepper motor has given up .looking on the chimaera pages parts list they give a parts no. of 73312. i have seen a one for sale with a parts no. of 73312a does anyone know if this will be ok or does the A make a differance.the one i have seen is on ebay at about 1/3 the price of one from dealers .any advice welcome .

blitzracing

6,422 posts

251 months

Wednesday 18th March 2009
quotequote all
Some of the low cost ones are from china, and the build quality can be poor as they let in air around the motor. Some do some dont, you takes your choice !

dc400

Original Poster:

125 posts

237 months

Wednesday 18th March 2009
quotequote all
hi Blitzracing,just thinking about the cheap one as the wallet is a bit short at the moment. the chim is sitting idle and the sun is coming out .i will have a think about it.thanks anyway.

SimonV8ster

13,039 posts

259 months

Wednesday 18th March 2009
quotequote all
I bought one off ebay as it was cheap compared to TVR websites/dealers, etc.

It was sh*t !! You could hear the air being sucked in through the join !!

V8 Animal

6,015 posts

241 months

Wednesday 18th March 2009
quotequote all
dc400 said:
hi Blitzracing,just thinking about the cheap one as the wallet is a bit short at the moment. the chim is sitting idle and the sun is coming out .i will have a think about it.thanks anyway.
It will carry on if you buy one from ebay LR indie £70 approx.

S7Paul

2,103 posts

265 months

Wednesday 18th March 2009
quotequote all
Don't buy the cheap ones - mine also leaked so I returned it. Eventually bought a decent one for about £55 (from one of the main online LR spares stockists).

dc400

Original Poster:

125 posts

237 months

Wednesday 18th March 2009
quotequote all
thanks for all your replys it looks like, no easter eggs for anyone this year .i will start looking for a lr one tommorow . thanks again all.

dickbastardly

450 posts

239 months

Wednesday 18th March 2009
quotequote all
hi
Just a warning, i followed the advive for stepper motors from here
http://www.chimaerapages.com/resources_partslist.p...
and the Landrover part no ERR5199 didnt fit! i managed to get it to fit but the wiring was all wrong!
Regards
Andy

dc400

Original Poster:

125 posts

237 months

Thursday 19th March 2009
quotequote all
hi Dickbdly/Andy. i have another lr part no. for the stepper motor.etc6660. range rover part .i will take stepper off tonight to see if it has any no.s or marks that give any more info .thanks for the warning . DEREK.

blitzracing

6,422 posts

251 months

Thursday 19th March 2009
quotequote all
Have you tried stripping it out ? I dont think they wear out as such, just gunk up. You can try this method I use, but its seriously noisy !

1) Get the car warm

2) Remove the stepper from the plenum and reconnect it.

3) Hold the stepper in your hand, so you can catch the central cone and spring when it comes out.

4) Get someone to start the car. Without the stepper in place it will rev at around 2k- 2.5k (This is noisy!!), but the ECU will try to slow it down by powering the stepper motor and pushing cone outwards. It will do this in a series of pulses, a few seconds apart, until the cone and spring drop out. (assuming they are not completely stuck). It may take a bit of manual help to get the cone to fully release. Now stop the engine and let it cool.

6) Clean all the muck off the shaft, and lightly lubricate the screw thread inside the motor.

7) To reassemble, wind the shaft back into the motor so far, but align the slot in the shaft with the plastic keyway as best you can by rotating the shaft in its screw thread

8)With the engine cool, then reconnect the stepper motor. Power cycle the ignition on and off, (don't start) and the ECU will try to pull the shaft back in each time the ignition is turned OFF. This is the slightly tricky bit, as if the keyway and shaft are not quite aligned it wont pull home, so you may need a few attempts.