car will not start
car will not start
Author
Discussion

MARKS6900

Original Poster:

306 posts

233 months

Thursday 19th March 2009
quotequote all
Hello, i have just bought a project car, a 98 400 chimaera that was supposed to run ok, i have fitted a new battery and filled the fuel tank with fresh fuel, the fob locks and unlocks the doors ok, the alarm light on the dash works ok, when i turn the ignition key the fuel pump works and you can hear certain clicks from the fuse box, the engine turns over ok, i have a voltage at both terminals of the coil, but no spark at the spark plugs, can somebody help with some advice please, also i noticed near the battery, ecu, that there is some wiring plugs but nothing connected, there are 2 yellow, 1 blue and 1 black connected to what looks like flasher units, 1 black 4 wires, 1 black with 6 wires, is this anything to do with it not starting, thank you.

debaron

878 posts

228 months

Thursday 19th March 2009
quotequote all
Pop out a spark plug and earth against the block of the engine. Kick the starter over and confirm an actual spark at the plug.

I wouldn't worry about the wiring loom plugs - I have several with nothing attached. You do want to check that you have 2 silver square box shaped things attached to the ECU wiring at various points though.

One is the fuel pump relay (which is probably what you can hear ticking from the footwell) - Other is the ignition relay. If you have HT at the coil then probably not that.

I'd suspect the ignition amplifier if no spark at the plugs or maybe rotor arm making poor contact.

MARKS6900

Original Poster:

306 posts

233 months

Thursday 19th March 2009
quotequote all
Hi, i have removed a spark plug and held it against engine no spark, i have also fitted a high tension lead tester between lead and plug no spark, yes i have the 2 silver boxes connected, where abouts is the ignition amplifier, where do you get a replacement from, thank you.

debaron

878 posts

228 months

Thursday 19th March 2009
quotequote all

The Ignition Amp is attached to a metal heat sink by the coil. It SHOULD have black and red input wires with a rubbery blue plug on the end. It only takes 2 screws to remove and is a pretty straightforward job.

You can get one here:


http://www.britishparts.co.uk/.sc/ms/bdd/ee/924/IG...


Do yourself a favour and get down to your local PC/Computer shop and buy some heatsink compound - It's white silicon based paste (£3-4) that transfers heat extremely effectively. Smear plenty on the metal side of the new Amp when fitting to aid cooling.


Note - Unscrew the screws BEFORE trying to remove the little blue plug - It is designed to be held in place by the amp itself. Also fit the blue plug in before screwing the new amp on.




Hope this helps


Ryan

debaron

878 posts

228 months

Thursday 19th March 2009
quotequote all

Actually, that part might be the 3 pin input module. You'll probably need the 2 pin one....Best phone them and ask to clarify. They may have the 2 pin

MARKS6900

Original Poster:

306 posts

233 months

Thursday 19th March 2009
quotequote all
Hi, just taken the ignition module off the car, it has a 3 pin plug on the top and a 2 pin plug at the back, it has 4SF-12KO59AA in white lettering plus 84493a 0185 on it made by lucas, thanks.

MARKS6900

Original Poster:

306 posts

233 months

Friday 20th March 2009
quotequote all
Hi, fitted new ignition modual, distributer cap and rotar arm, car started, ran for about 2 seconds then cut out, will not start, no spark, not happy just spent £80-, how can you tell if the ignition modual is up the swanny already, is it right that the 2 terminals on the coil are positive as 2 wires go from the coil into the ignition modual 2 pin plug, the 2 wires that come out of the modual 3 pin plug does that go to the distributer, also when i turn the ignition on you can hear the fuel pump but it never stops ticking, should it not stop when the fuel reaches the engine, thank you.

big geoff

387 posts

231 months

Friday 20th March 2009
quotequote all
fuel gague can read low but the tank is dry pump stays running stick some fuel in it

MARKS6900

Original Poster:

306 posts

233 months

Friday 20th March 2009
quotequote all
Hi i have put 15 ltrs in it, still fuel pump clicks, i can spell fuel when trying to start car, but no spark.

GreenV8S

31,027 posts

315 months

Friday 20th March 2009
quotequote all
Fuel smell suggests that the ECU is seeing a signal from the dizzy.

Does the coil work? With the ignition on, if you momentarily earth the -ve terminal you should get a spark on the king lead when you unearth it.

debaron

878 posts

228 months

Saturday 21st March 2009
quotequote all

Hi Mark,

It's unlikely that the ignition module has had it already unless there is something seriously wrong with the wiring etc.

Sounds like you have an intermittent spark problem. Clean the contacts to and from the coil (those nasty little spade connectors) they may have become corroded over time. Check for cracks in the wiring. The under bonnet temps can make wire very brittle and prone to crack. Double check that the king lead is firmly on the coil and making good contact (mine has slipped off so I cable tied the f**ker on). Open the terminals up inside the lead with pliers if need be

Check that all HT leads are pressed FIRMLY onto the extenders. If using non standard shrouded leads, the shrouds can travel down not allowing the metal terminals to make contact.

Also take a look at the 100 AMP fuse underneath the car too although I think that's more a 'total power failure' when that goes.

The fuel pump should definitely stop priming after a second or 2. Not sure what's going on there. May pressure regulator is stuck open?

Get a good healthy spark first then we'll try and solve the fuel pump problem!


Ryan

debaron

878 posts

228 months

Saturday 21st March 2009
quotequote all

Just thinking you might have a bad earth. Check in engine bay by the drivers footwell and I believe the earth point is around there. Give it a nice clean up and see if that helps!

MARKS6900

Original Poster:

306 posts

233 months

Saturday 21st March 2009
quotequote all
Hi, fitted another new module today, it started great i thought but it cut out after a couple of seconds, i checked the wiring and found the 3 pin plug at the back of the metal plate that the modual bolts to to have a bad connection cleaned it up, car would start but cut out and after a few goes it kept running left it for about 1/2 an hour, until i noticed exhaust was getting a bit hot just sitting there, all i need now is a new wishbone, a set of alloys, and a bit of luck with dvla to get her back on the road, thank you for all advice.