Refitting the mesh grill on a '95 Chimaera
Discussion
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.
However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
SteveW8975 said:
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.
However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
Yeah have to agree a pain in the arse.However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
But it's a case of once youv'e done it a few times it get's easier.
Still dread it though.
How i tackle it.
Put bottom in first and bow it so you can get both ends a part way in the gasket.
Then i use a flat blade screwdriver to wiggle the gasket over the top of the grill working from one corner to the middle.
Keep levering down to push the grill fully down into the gasket.
Once youv'e reached the middle and one side is in go over to other corner and leaver the grill towards the corner you have done it will help position the grill better and make your last corner easier.
Be carefull with the screwdriver you can easy slip with temper and scratch your paint.
Hope that helps looks awful without the grill.
V8 Animal said:
SteveW8975 said:
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.
However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
Yeah have to agree a pain in the arse.However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.
What's the answer?!
But it's a case of once youv'e done it a few times it get's easier.
Still dread it though.
How i tackle it.
Put bottom in first and bow it so you can get both ends a part way in the gasket.
Then i use a flat blade screwdriver to wiggle the gasket over the top of the grill working from one corner to the middle.
Keep levering down to push the grill fully down into the gasket.
Once youv'e reached the middle and one side is in go over to other corner and leaver the grill towards the corner you have done it will help position the grill better and make your last corner easier.
Be carefull with the screwdriver you can easy slip with temper and scratch your paint.
Hope that helps looks awful without the grill.

+1 but what a sod to get on,took me over an hour first time fingers and patience in tatters....just when you think its in it pops out..mmmmmm sounds familiar!!!

[/quote]
I slide it in from the RH side until it is in all the way from the left to the middle. Then gently pull the seal back
What was the topic again ive had a few

V8 Animal said:
+1 but what a sod to get on,took me over an hour first time fingers and patience in tatters....just when you think its in it pops out..mmmmmm sounds familiar!!!

V8 Animal said:
I slide it in from the RH side until it is in all the way from the left to the middle. Then gently pull the seal back
What was the topic again ive had a few
You didn't read my post either! What was the topic again ive had a few


Edited by Red Cabbage on Sunday 22 March 08:46
Badmutha said:
SteveW8975 said:
Cheers fellas - I'll give it another bash this afternoon.
I did notice how grubby the seal was yesterday when i took it off, so scraped out all of the gunk then, but washing up liquid/silicon spray/ky jelly sounds a helpful option!
I did notice how grubby the seal was yesterday when i took it off, so scraped out all of the gunk then, but washing up liquid/silicon spray/ky jelly sounds a helpful option!
don't waste the ky jelly!!!
Please forgive me for being blunt guys but you're all p***ing into the wind with your KY, washing up liquid, silicone lubricant and whatever you're having yourself solutions to the front grill refitting problem.
It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.
When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.

Changing a bulb now takes two minutes not two days.
I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.
Hope this helps.
It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.
When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.

Changing a bulb now takes two minutes not two days.
I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.
Hope this helps.
SpudMurphy said:
Please forgive me for being blunt guys but you're all p***ing into the wind with your KY, washing up liquid, silicone lubricant and whatever you're having yourself solutions to the front grill refitting problem.
It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.
When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.

Changing a bulb now takes two minutes not two days.
I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.
Hope this helps.
+1, used some tight fitting black grommet strip from Halfrauds, needed to heat it with a hair dryer and superglue around the bends. Now fixed with two self tapers, the heads of which blackened with permanent marker. Job done !It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.
When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.

Changing a bulb now takes two minutes not two days.
I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.
Hope this helps.
Hmmm, when mine was only attached with 2 central fixings it rattled like skeletons fornicating.. I subsequently used 4 fixings at the edges of the cross braces, it still flapped a bit until I added another two at the sides. This has been fine with the mesh and punched ally versions. 6 screws are still a lot easier than the tight rubber fitment
ooer: 
ooer: 
Gassing Station | Chimaera | Top of Page | What's New | My Stuff







