Solid vs Hydraulic lifters
Discussion
Zumbruk said:
I've just had my top end rebuilt, with hydraulic lifters and it doesn't tap at all. The rockers and cam were utterly shagged on my old engine, so it was a tad clattery... 
Hi Zumbruk, I had my engine apart not too long ago and the cam looked good, as did the rest of the rocker gear. It is possible, as Spend said, that an adjustable pushrod is just catching the head or one of the rockers is catching something. Since i plan to re-investigate i may be in the mood to replace the followers with solid ones. My question is whether there is a real benefit to this in performance etc. I really dont care about the engine being tappety if it is supposed to be. its just the annoying noises that should not be there 

More positive actuation of the valve 
Only downside is adjusting the clearances occasionally. Thats makes roller rockers with lash adjusters very desirable compared to 'fiddling' with bloomin adjustable pushrods.
You do set the clearances so that there can be slight tappety sound whilst cold, but as soon as all is warm & oiled you at least know any noises are significant screams for attention. Generally if they start clattering its a good sign that you need to check the clearances PDQ!. Suitable parts assembled correctly should have a lot less to go wrong as well
Call Rob, I think he might make your mind up for you if you ask the right questions...

Only downside is adjusting the clearances occasionally. Thats makes roller rockers with lash adjusters very desirable compared to 'fiddling' with bloomin adjustable pushrods.
You do set the clearances so that there can be slight tappety sound whilst cold, but as soon as all is warm & oiled you at least know any noises are significant screams for attention. Generally if they start clattering its a good sign that you need to check the clearances PDQ!. Suitable parts assembled correctly should have a lot less to go wrong as well

Call Rob, I think he might make your mind up for you if you ask the right questions...
Hydraulic lifters limit the rev range you can use, so if you plan to increase this significantly above standard you would need solid lifters. Hydraulic lifters flex more than solid ones so when changing between the two you need a different cam profile to get the equivalent effect. Solid lifters don't adjust to compensate for thermal expansion and wear, so you can expect the solid lifters to be noisier than hydraulic most of the time - and get worse over time needing adjustment a couple of times a year. Unless you actually *need* the extra rev range my feeling is solid lifters are a backwards step.
I take strong issue with that Peter, yes you can rev them higher if you want to, but both Joo & Pascos car on solids use FA more revs than when they were hydraulic cars. I believe what you are seeing is that at the higher RPMS the cam still lifts positively so they are getting all the partial through full opening that the cams are designed for.
Certainly with the stroked cars you can use wilder cams (softened by the capacity) but as far as revs go you are more limited by the increased piston speeds I would guess? The stronger solid cams are just using as much lift as is available AFIK, there are of course racier cams either solid or fluffy's that can be designed for different rev ranges. I don't know the exact figures but I would hazard a guess that the hydraulic lifters could start being +/- 0.1" valve lift at 4500rpm (just an illustration of the idea) and become progressively worse as revs rise.
Certainly with the stroked cars you can use wilder cams (softened by the capacity) but as far as revs go you are more limited by the increased piston speeds I would guess? The stronger solid cams are just using as much lift as is available AFIK, there are of course racier cams either solid or fluffy's that can be designed for different rev ranges. I don't know the exact figures but I would hazard a guess that the hydraulic lifters could start being +/- 0.1" valve lift at 4500rpm (just an illustration of the idea) and become progressively worse as revs rise.
Ah, although non rover the ls7 uses hydraulics, a roller cam and some hairy lift and it revs past 7k. I'm not a fan of solids although I do find some easier to adjust the others. I would consider them if I was after max bhp but most of the time I'd settle with hydraulics. Solids probably to sharpen up response time though.
AJP use shims, RV8 screwed adjusters.. very different maintenance procedure.
If someone charged you £350 for adjustment on an RV8 you would be farting very quietly for a while
Its about an hours work when you are prepared and know what you are doing (just add some time for tricky to get at adj pushrods if necessary).
For someone like the OP who put his own engine in, etc. Its just a Sunday morning wash/polish session twice per year swap
If someone charged you £350 for adjustment on an RV8 you would be farting very quietly for a while

Its about an hours work when you are prepared and know what you are doing (just add some time for tricky to get at adj pushrods if necessary).For someone like the OP who put his own engine in, etc. Its just a Sunday morning wash/polish session twice per year swap

spend said:
If someone charged you £350 for adjustment on an RV8 you would be farting very quietly for a while 




Have no problem with adjusting on occasion. But need a bit more convincing it is worth changing.
Are the hydraulic followers partly responsible for the power dropping off from 5500rpm? I know the cam profile will play a major part in this...
Gassing Station | Chimaera | Top of Page | What's New | My Stuff






Oh they are fat & ugly 
