Exhaust manifold shopping
Discussion
So the good news on this morning's MOT was that my Chimmie was granted one without any expenditure needed other than the test itself 
; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months.
The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams
) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).
Now if there's one thing I like it's shopping - for shiny TVR stuff, that is!
- and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. 
Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).
Recommendations?

; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months. The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams
) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).Now if there's one thing I like it's shopping - for shiny TVR stuff, that is!
- and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. 
Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).
Recommendations?

http://www.v8enhancements.co.uk/
Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.
Uncle Fester said:
http://www.v8enhancements.co.uk/
Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

They also gave me an extra 27hp & 50lb/ft.Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.
900T-R said:
So the good news on this morning's MOT was that my Chimmie was granted one without any expenditure needed other than the test itself 
; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months.
The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams
) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).
Now if there's one thing I like it's shopping - for shiny TVR stuff, that is!
- and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. 
Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).
Recommendations?
Glad everything else seems good on the Chim 
; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months. The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams
) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).Now if there's one thing I like it's shopping - for shiny TVR stuff, that is!
- and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. 
Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).
Recommendations?


Not sure what manifolds are available but what you want are long tube headers. This is because for a n/a motor exhaust scavenging is far more important than outright flow. In fact many standard manifolds actually flow quite well for the stock level of HP, so unless massivly upping the power levels only minimal gains will be seen by flow increase.
In order to scavnege the primaries need to be long, the longer the better as it will promote scavenging at lower rpms, and as we all know the Rv8 is hardly a revver at the best of times.
griffdude said:
Uncle Fester said:
http://www.v8enhancements.co.uk/
Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

They also gave me an extra 27hp & 50lb/ft.Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

I know they're good value Clive, just not in relation to the value of the average Chim though...
If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ 
Anyway... WTF is up with this here http://cgi.ebay.co.uk/TVR-ROVER-V8-EXHAUST-MANIFOL... ?

On the right side of the pic a pre-cat manifold, on the left ????
If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ 
Anyway... WTF is up with this here http://cgi.ebay.co.uk/TVR-ROVER-V8-EXHAUST-MANIFOL... ?
On the right side of the pic a pre-cat manifold, on the left ????
Right, options found so far.

Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included
, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)
Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?

Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description
- SH std de-precat manifolds + this:

Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included
, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?
- ACT 'performance' manifolds & Y-piece package:

Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?
- TVR Car Parts Chim/Griff manifolds including Y-piece:

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description
The precat ones are nice in that they have long primaries, but the tight bend around the front of the engine might be a disadvantage. TVR's big collector and nice big diameter around the bend is not as daft as it seems, but I suspect was more influenced by positioning the lambda sensor than anything else
I'm yet to be convinced that there are significant advantages to either alternative when going into the y-piece?
I've got a good set of flanged manifolds Eric if you can convince Cliff to make a Y-piece with flanges, rather than the "Band-It" (c) contraptions. I know you're a stickler for originality
I'm yet to be convinced that there are significant advantages to either alternative when going into the y-piece?I've got a good set of flanged manifolds Eric if you can convince Cliff to make a Y-piece with flanges, rather than the "Band-It" (c) contraptions. I know you're a stickler for originality

900T-R said:
I know they're good value Clive, just not in relation to the value of the average Chim though...
If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ 
sorry mate, didn`t realise you were a johnny foriegner
If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ 

900T-R said:
Right, options found so far.

Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included
, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)
Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?

Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description
Your getting confused, the picture you show for ACT manifolds is infact V8S, nothing like our Griff/Chim manifolds- SH std de-precat manifolds + this:

Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included
, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?
- ACT 'performance' manifolds & Y-piece package:

Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?
- TVR Car Parts Chim/Griff manifolds including Y-piece:

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description
ACT said:
Your getting confused, the picture you show for ACT manifolds is infact V8S, nothing like our Griff/Chim manifolds
Ah, but that's the pic in your own manifolds web shop page shows for the Chim/Griff manifolds... (and yes I did notice that it said 'v8s' when I copied the URL) 
Edited by 900T-R on Friday 27th March 19:25
I have the Peninsular stainless manifolds and Y-piece on my '92 Griff 430. They were put on by the previous owner so I can't say what improvement(s) it made on what it was before. But... it sounds great and shows good numbers if that's what you're looking for.
Being a bit of a knob though, I'm binning them this Spring in favour of V8 Enhancements 1.3/4" tuned manifolds - they look great, sound better and more grunt - no brainer really. There's a short video but it doesn't really do them justice: click.
I'm also having some other work done soon after to further enhance it so I'll be interested to see how it drives by the Summer.
Should be schmokin'!
Being a bit of a knob though, I'm binning them this Spring in favour of V8 Enhancements 1.3/4" tuned manifolds - they look great, sound better and more grunt - no brainer really. There's a short video but it doesn't really do them justice: click.
I'm also having some other work done soon after to further enhance it so I'll be interested to see how it drives by the Summer.
Should be schmokin'!

Gassing Station | Chimaera | Top of Page | What's New | My Stuff





