spark plug NGK B7ECS
spark plug NGK B7ECS
Author
Discussion

hiltonig

Original Poster:

3,153 posts

239 months

Wednesday 25th March 2009
quotequote all
anyone found a better plug than this >???

hiltonig

Original Poster:

3,153 posts

239 months

Wednesday 25th March 2009
quotequote all
ok is there such a thing as an alternative ??

450Nick

4,027 posts

243 months

Wednesday 25th March 2009
quotequote all
Why?? I use B8ECS on my SC'd one as it runs a bit cooler but as I understand it, the B7 is intended for TVR RV8's as when I spoke to them, its not used on anything else!

lewis_sharman

5,958 posts

222 months

Wednesday 25th March 2009
quotequote all
What is the equivalent Bosch plug with the four electrodes?

I know a lot of people don't rate the 'performance' plugs, but since i'm changing them it can't hurt?

Pupp

13,043 posts

303 months

Wednesday 25th March 2009
quotequote all
The 7ECS is a good plug for the application. The electrode is a stonger type (so more resistant to knock damage) and the heat range is more than cool enough (loads of guys use 6s and even 5s in RV8s, can't imagine why you'd want to go colder still, even in a blown motor. Just asking for cold foul issues

450Nick

4,027 posts

243 months

Wednesday 25th March 2009
quotequote all
Because the man at NGK told me to boxedin

Adrian@

4,667 posts

313 months

Wednesday 25th March 2009
quotequote all
I had a 500 that had a shift light system...this would feed back resistance type flashes of all the lights if the plugs were failing under load, initially the odd flash, but as the flashes got more regular, it related to a load related miss-fire when pushing on, that would be cured by replacing the plugs. Over the period that I owned the car I tried lots of different plugs to stop this! I cannot say that I did ever cure it, but the B7ECS lasted the longest.
Adrian@

GreenV8S

31,027 posts

315 months

Wednesday 25th March 2009
quotequote all
Pupp said:
The 7ECS is a good plug for the application. The electrode is a stonger type (so more resistant to knock damage) and the heat range is more than cool enough (loads of guys use 6s and even 5s in RV8s, can't imagine why you'd want to go colder still, even in a blown motor. Just asking for cold foul issues
I'm running 8s now, although I ran 6 in the early stages of tuning while it was running mega rich. I also run resistive plugs (BPR).

wheels1

209 posts

219 months

900T-R

20,406 posts

288 months

Thursday 26th March 2009
quotequote all
lewis_sharman said:
What is the equivalent Bosch plug with the four electrodes?

I know a lot of people don't rate the 'performance' plugs, but since i'm changing them it can't hurt?
If experiences with replacing similar NGK plugs in turbo Saabs with those Bosch plugs are anything to go by - don't. Not sure I've ever had, or heard of, good luck replacing anything high performance of which the manufacturer specifies NGK, with another brand of super dooper plugs.

That Daddy

19,466 posts

252 months

Thursday 26th March 2009
quotequote all
Bos*h are st don't use em,had about two duff NGKs(all i fit apart from Denso when no stocks of NGK)and that spans over 23 years of the motor trade thumbup multi electrodes are only for longer service intervals,not multiple sparks biggrin NGK work over a wider heat range too compared to most,nuff said smile





Edited by That Daddy on Thursday 26th March 10:33

rigga

8,808 posts

232 months

Thursday 26th March 2009
quotequote all
Must admit ive never head anything bad about NGK plugs,lots of stories regarding other makes though,this is bikes and cars.......

That Daddy

19,466 posts

252 months

Thursday 26th March 2009
quotequote all
My philosophy with bikes was Japanese bikes Japanese plugs simple ; Denso or NGK no substitute smile don't work on em any more though frown

f@-pots

204 posts

234 months

Thursday 26th March 2009
quotequote all
I know nothing about the resisted or non resisted plug subject , but I'd like to know why you would use resisted plugs, and if you do , are you supposed to have resisted leads and extenders? Put simply , what are the correct combinations of either resisted or non resisted components from dizzy to plug ? And what effect can the incorrect parts have on performance ?

Ta in advance , Nick...................

900T-R

20,406 posts

288 months

Thursday 26th March 2009
quotequote all
There's no 'R' in the specified plugs so TVR didn't think our cars need them... Saabs got resistor plugs when they went to computerized coil-on-plug ignition (DI/Trionic).

spend

12,581 posts

282 months

Thursday 26th March 2009
quotequote all
Without resistance you wont get a crisp spark wink Theoretically you can 'fiddle' with it to be anywhere in the plug and/or leads and/or caps.., coils are designed to work with a certain resistance in the plug/leads - whether coil/dizzy, coil packs.... TBH closer to the plug away from other electrics seems sensible to me, but there have been many reports unsuccessful attempts of deploying resistive plugs IIRC?.

Simplistically there isn't a right/wrong way as long as the resistance from coil - plug electrode is matched to the particular coil being used.

EMF spike problems are more down to poor cable routing / particularly suspect types of leads as I understand it.

rigga

8,808 posts

232 months

Thursday 26th March 2009
quotequote all
Pupp said:
loads of guys use 6s and even 5s in RV8s, can't imagine why you'd want to go colder still, even in a blown motor. Just asking for cold foul issues
Interesting comment regarding the use the reccomended heat range plugs...... would this be in otherwise standard engines? and for what purpose?.....interested as i did suffer with cold start issues,greatly helped now with the replacement of the duff vac advance unit,but fitting 6 grade plugs might also help in this situation further?

900T-R

20,406 posts

288 months

Thursday 26th March 2009
quotequote all
There's nowt in a TVR RV8 to keep its engine from dying a horrible death by detonation - I would therefore desist from installing hotter plugs unless I was only using my car for popping to the shops in s Driving Miss Daisy style.

I assume the 5 and 6 range plugs are for low compression, mild cammed RV8 versions in Rangies and old Rovers, not for TVR Power-fettled ones...

Edited by 900T-R on Thursday 26th March 16:17

rigga

8,808 posts

232 months

Thursday 26th March 2009
quotequote all
900T-R said:
I assume the 5 and 6 range plugs are for low compression, mild cammed RV8 versions in Rangies and old Rovers, not for TVR Power-fettled ones...
This was what i wanted clearing up really.....

hiltonig

Original Poster:

3,153 posts

239 months

Thursday 26th March 2009
quotequote all
That Daddy said:
Resistor spark plugs use an integral resistor to absorb the radio frequency energy generated from the spark,non resistor spark plugs can cause massive radio frequency interference which can affect the electronics in certain vehicles,the Chim leads are supposed to be resisted along with the extenders and the ECU in these cars is not finicky with RF interference although your ICE might be frown i have the CRE resisted leads with non resisted extenders(also CRE)and BP7ES plugs fitted,no need to fit the TVR exclusive B7 ECS plugs in my opinion.







Edited by That Daddy on Thursday 26th March 13:14
Glad someone asked that one as I have coilpacks and magacore KV85 leads, I know when it was Emerald being setup there was a debate to fit resistive plugs, not sure what was fitted so next week I am going to have them all out to check plug numbers,