Brake problems HELP !
Brake problems HELP !
Author
Discussion

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
Just completed a bigger brake upgrade on the front. Used Granada / Mondeo V6 calipers (887 & 888) with larger discs. All was going well until I started bleeding the air out of the system. Yesterday we tried the two man method, no more apparent air in the system but the pedal was floored after a couple of pumps. Went to Halfrauds today and bought an easy bleed, one that uses pressure from a spare wheel. Bled all four wheels twice, again no apparent air in the system but the pedal is just the same. Took the car up the road and the brakes barely stop it at 10 mph.
What do ya reckon folks, have I destroyed the master cylinder ? Any thoughts ??

Roy.

STE VR

501 posts

237 months

Sunday 29th March 2009
quotequote all
Does the pedal offer ANY resistance when going to the floor?

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
Yes it does, feels quite reasonable but pump it a couple of times and its floored

GreenV8S

31,027 posts

315 months

Sunday 29th March 2009
quotequote all
If the system has been drained then simply flushing fluid through is isn't always sufficient to get rid of air bubbles. You need to work through the whole system from the m/c outwards, working our where air pockets can collect in high spots and figure out how to chase them out. For example you might need to unbolt calipers to chase the air to the side with a bleed nipple, or slacken joints to let air out.

You will probably be spending a long time pumping air out before it's completely sorted. I find it helps to connect a long hose from the bleed nipple back up to the reservoir so I can pump the fluid round continually.

STE VR

501 posts

237 months

Sunday 29th March 2009
quotequote all
Must admit does sound like master cylinder problems. Just out of curiosity is the non-return valve ok in the cylinder under the dome shape cover on the drivers wing? When you have been bleeding the brakes its possible the master cylinder has been week and you have finished it off whilst bleeding.

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
GreenV8S said:
If the system has been drained then simply flushing fluid through is isn't always sufficient to get rid of air bubbles. You need to work through the whole system from the m/c outwards, working our where air pockets can collect in high spots and figure out how to chase them out. For example you might need to unbolt calipers to chase the air to the side with a bleed nipple, or slacken joints to let air out.

You will probably be spending a long time pumping air out before it's completely sorted. I find it helps to connect a long hose from the bleed nipple back up to the reservoir so I can pump the fluid round continually.
Thanks for that, will spend some more time doing as you say. Hope that's the case as I really don't fancy working in the foot well replacing the master cylinder.

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
STE VR said:
Must admit does sound like master cylinder problems. Just out of curiosity is the non-return valve ok in the cylinder under the dome shape cover on the drivers wing? When you have been bleeding the brakes its possible the master cylinder has been week and you have finished it off whilst bleeding.
I haven't looked at the non return valve, how would I know if it's ok, is there a way of checking it ?

thanks

Bensonv8

470 posts

240 months

Sunday 29th March 2009
quotequote all
Does the original master cylinder move enough brake fluid to push all the pistons out on these "bigger" calipers. you might need the Granada/Mondeo master cylinder.

Where are the bleed nipples when you bolt them on ?
They need to be at the highest point on the caliper so there is no trapped air.

Mondeos seem to mount the caliper in front of the disc (leading), where as Chimaeras are mounted behind the disc (trailing)
So if you take the front mounted caliper and rotate it to the rear mounting position you are effectively, turning it upside down. therefore the bleed nipple will not be in the right place.

Unless you put the Mondeo right hand caliper on the left of your Chimarea. !??

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
Bensonv8 said:
Does the original master cylinder move enough brake fluid to push all the pistons out on these "bigger" calipers. you might need the Granada/Mondeo master cylinder.

Where are the bleed nipples when you bolt them on ?
They need to be at the highest point on the caliper so there is no trapped air.

Mondeos seem to mount the caliper in front of the disc (leading), where as Chimaeras are mounted behind the disc (trailing)
So if you take the front mounted caliper and rotate it to the rear mounting position you are effectively, turning it upside down. therefore the bleed nipple will not be in the right place.

Unless you put the Mondeo right hand caliper on the left of your Chimarea. !??
Bleed nipples are on top. This upgrade seems to be quite common and I haven't heard of anyone having to replace the master cylinder to. Have they ?...........

locodude

510 posts

226 months

Sunday 29th March 2009
quotequote all
Try lifting the rear calipers up at the back and then bleeding them. i.e undo the bottom bolt and swivel them up. Don't know why but sometimes the rears can collect air they don't want to get rid of. Worked for me.

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
locodude said:
Try lifting the rear calipers up at the back and then bleeding them. i.e undo the bottom bolt and swivel them up. Don't know why but sometimes the rears can collect air they don't want to get rid of. Worked for me.
Ah ok, although I haven't dismantled anything at the rear, and the front of the car was much higher than the rear when doing the work. Do you think that could still be a problem ?

GreenV8S

31,027 posts

315 months

Sunday 29th March 2009
quotequote all
roysum said:
STE VR said:
Must admit does sound like master cylinder problems. Just out of curiosity is the non-return valve ok in the cylinder under the dome shape cover on the drivers wing? When you have been bleeding the brakes its possible the master cylinder has been week and you have finished it off whilst bleeding.
I haven't looked at the non return valve, how would I know if it's ok, is there a way of checking it ?

thanks
I think what you're describing is the bias valve. It has not got any non-return function, and unless you've got air in it is unlikely to cause trouble.

I'm intrigued by the symptoms that the brakes get *worse* when you pump them. Normally it's the other way round - brakes feel rubbish at the first attempt but improve when pumped.

locodude

510 posts

226 months

Sunday 29th March 2009
quotequote all
roysum said:
Ah ok, although I haven't dismantled anything at the rear, and the front of the car was much higher than the rear when doing the work. Do you think that could still be a problem ?
It's happened a few times to me with ford rear calipers used on other vehicles (kit cars etc). Just try to get the bleed nipple as high as possible. Might not be the solution but at least ineliminates a possible.

roysum

Original Poster:

961 posts

220 months

Sunday 29th March 2009
quotequote all
GreenV8S said:
roysum said:
STE VR said:
Must admit does sound like master cylinder problems. Just out of curiosity is the non-return valve ok in the cylinder under the dome shape cover on the drivers wing? When you have been bleeding the brakes its possible the master cylinder has been week and you have finished it off whilst bleeding.
I haven't looked at the non return valve, how would I know if it's ok, is there a way of checking it ?

thanks
I think what you're describing is the bias valve. It has not got any non-return function, and unless you've got air in it is unlikely to cause trouble.

I'm intrigued by the symptoms that the brakes get *worse* when you pump them. Normally it's the other way round - brakes feel rubbish at the first attempt but improve when pumped.
Yes, that's what has puzzled me. Initially the pedal feels good, push on it a couple of times and down it goes !

GreenV8S

31,027 posts

315 months

Monday 30th March 2009
quotequote all
roysum said:
GreenV8S said:
roysum said:
STE VR said:
Must admit does sound like master cylinder problems. Just out of curiosity is the non-return valve ok in the cylinder under the dome shape cover on the drivers wing? When you have been bleeding the brakes its possible the master cylinder has been week and you have finished it off whilst bleeding.
I haven't looked at the non return valve, how would I know if it's ok, is there a way of checking it ?

thanks
I think what you're describing is the bias valve. It has not got any non-return function, and unless you've got air in it is unlikely to cause trouble.

I'm intrigued by the symptoms that the brakes get *worse* when you pump them. Normally it's the other way round - brakes feel rubbish at the first attempt but improve when pumped.
Yes, that's what has puzzled me. Initially the pedal feels good, push on it a couple of times and down it goes !
I've got a suspicion it may be something to do with the way the circuits are split in the m/c by that floating piston, but I can't quite get my head around it.

Starting from scratch if you push the pedal hard once and hold it down, does the pedal stay solid? If your glamorous assistant then goes round the callipers do you have pressure in both front and rear circuits?

roysum

Original Poster:

961 posts

220 months

Monday 30th March 2009
quotequote all
GreenV8 said
I've got a suspicion it may be something to do with the way the circuits are split in the m/c by that floating piston, but I can't quite get my head around it.

Starting from scratch if you push the pedal hard once and hold it down, does the pedal stay solid? If your glamorous assistant then goes round the callipers do you have pressure in both front and rear circuits?

Reply.....
Tonight I sat in the car and the pedal feels very firm, that's without the engine running (ie no servo) and doesn't go down. I'm going to try it presently with the engine running, Had a look in the footwell, bleeding hell in there to replace the m/c !
Back shortly.
Roy

HRG

72,863 posts

270 months

Monday 30th March 2009
quotequote all
Have you double checked the hoses?

roysum

Original Poster:

961 posts

220 months

Monday 30th March 2009
quotequote all
HRG said:
Have you double checked the hoses?
Ok, lifted her up and no leaks. Pedal firm, start engine and with continual pressure on the pedal it slowly goes to the stop.

HRG

72,863 posts

270 months

Tuesday 31st March 2009
quotequote all
It's leaking past a seal somewhere...

roysum

Original Poster:

961 posts

220 months

Tuesday 31st March 2009
quotequote all
HRG said:
It's leaking past a seal somewhere...
mmm, going to do a thorough bleed again and see. Horrible feeling it's the m/c. phoned Racing Green today, who said it was unusual for them to go, reckon about £375 +VAT which includes pick up.

Spoke to a local one man MOT tester / mechy who said that it's quite rare now for m/c's to be a problem. But not so long ago Fords and Vauxhalls used to let go !

Might have ago myself, although not looking fwd to it.

Please keep any advice coming, really appreciate it.

Thanks, Roy.