Induction System Upgrades - Pictures
Induction System Upgrades - Pictures
Author
Discussion

debaron

Original Poster:

878 posts

228 months

Sunday 29th March 2009
quotequote all
Evening all,

Over the past 2 weeks I've had the chance to do some upgrades to the induction system.


It all started out as a small job to get the injectors out for cleaning. Having realised (after much pulling, puffing, sweating and swearing) that I was going to have to take off everything down to the trumpet base to get the fuel rail off, I decided to do:

- SC Power Heat Shield Gasket
- SC Power Plenum Spacer
- ACT Induction Kit with K+N Filter
- Clean and Polish Trumpets
- Injector Overhaul


I've documented some parts of the project below if anyone is thinking of doing similar:



Filthy Trumpet Base:












The trumpet base was caked in grease and filth inside the pipes - Seeing as I was trying to keep the whole induction system as clean and smooth as possible, I wasn't having having any of that!

I cleaned them first with wire wool wrapped round a masonry drill bit. Worked a treat!

Then polished with kitchen roll soaked in Brasso








Then buffed with just kitchen roll!











Nice and shiny and noticeably smoother to the touch.



New Bits!







I was thinking of cutting down my trumpets but it sounded like a bit of a hassle so I decided on the spacer from SC Power. This gives the advantage of unshrouding the top of the trumpets while also increasing the Plenum Volume and therefore volumetric efficiency of the engine.



Injector Report:







They were flowing from 192 - 198 before cleaning - After cleaning they were all 212 CC/Min. No problems flagged up and new filters fitted in each.

NB - I'm not here to promote any persons services or products - but if you want your injectors doing:

www.injectortune.co.uk

James is a really nice guy - excellent service and really knows his stuff too - he even agreed to meet me on a Saturday to collect them seeing as I was too impatient to wait for the post!! AND refunded my postage costs!!!


Refitting:







Factory Fitted Cat!












Spacer piece in place between Trumpet Base and Plenum - Plenty of Hylomar Blue!

The heat shield is the bit of orange underneath.

I then fitted the ACT induction kit - It's a well known pig of a job documented in another thread so I've left it off here.


Done!







Conclusion:


On first drive the engine seems to rev more freely and be generally 'keener' - not by a huge margin but enough to notice.

The real difference is above 4000 RPM - The car seems to have more power whereas before it would get a bit lumpy and feel somewhat 'limited'.

If anyone is thinking of doing similar and wants any advice or recommendations please drop me a line.


Ryan








Edited by debaron on Sunday 29th March 21:30


Edited by debaron on Sunday 29th March 21:32


Edited by debaron on Sunday 29th March 21:34


Edited by debaron on Sunday 29th March 21:35


Edited by debaron on Sunday 29th March 21:42

AlRaven

408 posts

240 months

Monday 30th March 2009
quotequote all
Yep, thinking of doing similar. I've already done the ACT induction kit as although a bit of a pig it did seem suitable for a non-skilled person like me.

Next step I was considering was the plenum spacer so how much technical stuff is involved in fitting the spacer? and whose did you buy?

But then I got to looking at nice new ACT or similar trumpets as well........

But then I thought, perhaps save up for the Torqueflow system.............

debaron

Original Poster:

878 posts

228 months

Monday 30th March 2009
quotequote all

I got mine from SC Power


http://www.sc-power.co.uk/SC%20Power%20Engine%20Mo...


To be honest, it's not too bad a job. Taking the Plenum off is pretty straightforward. That's all you'll need to do if you want to just fit the spacer. You'll need to move the PAS reservoir (if fitted) and coil/Ignition Amp assembly plus a few vacuum hoses and the main air input.

If you want to do Injectors and heat shield gasket then the Trumpet Base will need coming off too.

daz the plumber

14,997 posts

262 months

Monday 30th March 2009
quotequote all
don`t think you need the plenum spacer if you go for eather carbon trumpets or just cut yours down .ive fitted the insulator between the trumpets base and inlet manifold ,carbon trumpets and a a.c.t induction kit ., im not sure if these gizzmos do anything at all.if i was going to spend any more money i would go all the way on the induction side of things .i would get a bored out plenum 72mm , larger 45mm trumpet base and a ported inlet manifold .can`t see the benifits unless you actualy get the air where it needs to be .ive looked at these three items and there not that expensive if you shop around , think at this point you will need a re map.more you move away from standard more the need to re chip . i think the act induction kit makes a difference but the other bits im not sure about .after all this work i would think about gas flowed heads , now all this together would transform your car .

blitzracing

6,422 posts

251 months

Monday 30th March 2009
quotequote all
It may not be worth your while polishing the inlet side of things as once school of though is the slightly rough surface causes the air to buffer along the inlet wall, and it helps stop fuel drop out (basically condensation) and improves the mixture of the fuel droplets into the air stream. I cant prove it, but I would not spend hours polishing to a mirror finish. Exhaust ports can be polished, but of course gets sooty pretty quicky.

spend

12,581 posts

282 months

Monday 30th March 2009
quotequote all
Thats only after introducing the fuel AFIK, I always used to polish upstream of the injectors, as in down the grades and real compound. This year I shall be mainly blasting & spraying them hehe

debaron

Original Poster:

878 posts

228 months

Monday 30th March 2009
quotequote all

Agreed with Spend. I read about fuel drop out on the G33 tuning pages - keeping the manifold walls rough after fuel has been introduced is paramount. Before fuel however, surely the induction path should be as smooth and as crease-free as possible to minimize parasitic power loss?