Number plate fell off - and scew thread is too big
Number plate fell off - and scew thread is too big
Author
Discussion

thegman

Original Poster:

1,928 posts

235 months

Monday 30th March 2009
quotequote all
So I was out on Sunday when I heard an awful scraping noise. I thought I must have run something over, but it turns out one of the screws holding in my number plate had come out.

I suspected this might happen as one of the original screws was loose in its thread. I want to fix this properly, so can somebody advise - should I use a self tapping screw with larger thread? Or should I fill the existing holes with epoxy filler first?

Thanks

sapper

1,134 posts

236 months

Monday 30th March 2009
quotequote all
I used the some screw, into some epoxy and had a couple of sticky pads to hold the plate in situ while the epoxy went hard, sticky pads still there and plate hasnt fell off, simple and easy fix biggrin

locodude

510 posts

226 months

Monday 30th March 2009
quotequote all
I've used 5mm aluminium rivnuts with a small amount of epoxy for good measure. Plate fastened with stainless 5mm cap screws.

LordGrover

34,191 posts

243 months

Monday 30th March 2009
quotequote all
My front plate is fastened with velcro. Enables swift removal and replacement if I accidentally still have my 'show' plate on the road. wink

thegman

Original Poster:

1,928 posts

235 months

Monday 30th March 2009
quotequote all
LordGrover said:
My front plate is fastened with velcro. Enables swift removal and replacement if I accidentally still have my 'show' plate on the road. wink
Where did you put the velcro - the screws were through the thin middle section - did you really get enough grip attaching the velcro here?

LordGrover

34,191 posts

243 months

Monday 30th March 2009
quotequote all
Ah. Mine's a precat Griff, much smaller 'mouth' so a larger flat area to stick the pads onto. Apologies. As you were.

ETA:


There's probably a way though ...


Edited by LordGrover on Monday 30th March 15:02

im

34,302 posts

248 months

Monday 30th March 2009
quotequote all
LordGrover said:
Ah. Mine's a precat Griff, much smaller 'mouth' so a larger flat area to stick the pads onto. Apologies. As you were.

ETA:


There's probably a way though ...
shout Lord Grover...THIS IS THE CHIMAERA FORUM.


biggrin

DavidLScott

1,048 posts

255 months

Tuesday 31st March 2009
quotequote all
My home made brackets:




thegman

Original Poster:

1,928 posts

235 months

Tuesday 31st March 2009
quotequote all
DavidLScott said:
My home made brackets:
smart!

Edited by thegman on Tuesday 31st March 11:46

TVR keith

1,917 posts

253 months

Tuesday 31st March 2009
quotequote all
Mines been fixed onto the thin middle section only using number plate tape.
Been there for 20k miles and nearly 4 years, it'll probably fall off now I've said this.
Make sure you get the tape warm with a hair dryer first

BoyzToyz

370 posts

241 months

Sunday 5th April 2009
quotequote all
thegman said:
So I was out on Sunday when I heard an awful scraping noise. I thought I must have run something over, but it turns out one of the screws holding in my number plate had come out. should I use a self tapping screw with larger thread? Or should I fill the existing holes with epoxy filler first?

Thanks
I used a suitable size of rawl plug and a smaller diameter screw - worked very well.

andykart

109 posts

227 months

Tuesday 7th April 2009
quotequote all
BoyzToyz said:
thegman said:
So I was out on Sunday when I heard an awful scraping noise. I thought I must have run something over, but it turns out one of the screws holding in my number plate had come out. should I use a self tapping screw with larger thread? Or should I fill the existing holes with epoxy filler first?

Thanks
I used a suitable size of rawl plug and a smaller diameter screw - worked very well.
yep i did the same and works very well...and its cheap!

Monkeylegend

29,595 posts

262 months

Tuesday 7th April 2009
quotequote all
God, these TVR's are just so unreliable !!!

HRG

72,863 posts

270 months

Tuesday 7th April 2009
quotequote all
LordGrover said:
Ah. Mine's a precat Griff, much smaller 'mouth' so a larger flat area to stick the pads onto. Apologies. As you were.

ETA:


There's probably a way though ...


Edited by LordGrover on Monday 30th March 15:02
Mine's a 500 and there's plenty of room for sticky velcro yes

Seasider

12,728 posts

280 months

Tuesday 7th April 2009
quotequote all
HRG said:
Mine's a 500 and there's plenty of room for sticky velcroyes




wink

LordGrover

34,191 posts

243 months

Tuesday 7th April 2009
quotequote all
Shush! They get all tetchy hereabouts.

This is for local people.

im said:
shout Lord Grover...THIS IS THE CHIMAERA FORUM.


biggrin

Alex L

2,596 posts

285 months

Tuesday 7th April 2009
quotequote all
Heavy duty Velcro from B&Q on mine..


HRG

72,863 posts

270 months

Tuesday 7th April 2009
quotequote all
Seasider said:
HRG said:
Mine's a 500 and there's plenty of room for sticky velcroyes




wink
Look at you and your posh smilies wink

It's stayed put at :cough: MPH biggrin

Seasider

12,728 posts

280 months

Wednesday 8th April 2009
quotequote all
HRG said:
It's stayed put at :cough: MPH biggrin
Thats when its supposed to have fallen orff wink

HRG

72,863 posts

270 months

Wednesday 8th April 2009
quotequote all
wink :tapsnose: Gotcha.