Lifting Roof
Lifting Roof
Author
Discussion

kris450

Original Poster:

740 posts

225 months

Tuesday 31st March 2009
quotequote all
Evening all

Noticed over the last few days that parts of the roof are lifting/unsticking from the body.

Hopefully the pics below can help out





Any ideas on sticking\securing it back as it should be ? Will this lead to something worse if I leave it ?

Please don't tell me I need a new roof !!

Chimjunkie

2,879 posts

242 months

Tuesday 31st March 2009
quotequote all
There are a few fasteners for the back part of the hood which can be adjusted to tension it properly. Probably a bit of a black art though..

snorky

2,322 posts

282 months

Tuesday 31st March 2009
quotequote all
take out the allen bolt fasteners, this can be a bit fiddly and be careful of your fingers with the exposed fibreglass in the boot. You'll need to drill out the pop-rivets either side these are 4mm ones I think and there is also a phillips screw on each side in a screw head cup (these are available from screwfix).The back of the roof is contact adhesived (real word?) to a fireglass hoop. Looks like your glue has given a bit. Mine was marked with pen where it went - it's usually cut into "fingers" to allow it to go around the hoop. Peel the hood off the hoop - clean all the old glue off as much as you can then re glue in original posn or, if it's not marked, a bit higher than it was when you remove it - small G clamps help with holding it in posn around the corners. Wait 24hrs or until glue has gone off then undo elbows - refit hoop with fasteners. IT's relatively easy just tae your time and be carefull with the glue not to get it where you'll see it. Bingo !

Edited by snorky on Tuesday 31st March 20:41

daz the plumber

14,997 posts

262 months

Tuesday 31st March 2009
quotequote all
its a big job , yours will end up looking like this , im taking mine to cerizma for a re fit and new plastic window

kenny Chim 4

1,604 posts

289 months

Tuesday 31st March 2009
quotequote all
Daz, your picture clearly shows one of the three bolts that are sited in the lower edge of the rear hoop.

The corresponding nuts for these are accessed via lifting out the carpet trim that's wedged above the fuel tank in the boot. In your case, it would be easy to tighten that nut to provide a tight fit to that section of the hoop.

Yes, it's a more tricky job than a previous poster suggested and it's all about balance of torsion of both the mohair and the rear plastic screen (forwards and sideways if you see what I mean).

For more tips, use the search on here to bring up the Griff Page that encouraged me to replace the last car's roof with the excellent Dave Hammerton kit.

daz the plumber

14,997 posts

262 months

Tuesday 31st March 2009
quotequote all
its pulled upwards and towards the boot , it now catches the boot when i lift it ,pulling it even more .cerizma will replace the plastic with a softer type matarial and re fit it for £170.it was replaced before i purchased the car but it s a bodge job !


Edited by daz the plumber on Tuesday 31st March 23:49

kenny Chim 4

1,604 posts

289 months

Wednesday 1st April 2009
quotequote all
Fair enough Daz and best of luck getting it sorted correctly.

I can't help but think that those boot nuts I referred to previously are not in situ/tightened though as your last photo seems to show the glint of the middle bolt appearing above the bodyscratchchin

DavidLScott

1,048 posts

255 months

Wednesday 1st April 2009
quotequote all
Mine's gone the same way - I assume it is the tension of the roof (which is pretty tight on mine) that pulls against it.

I'm living with it for the moment but will probably decide it looks too manky later this year and get it done professionally (as opposed to my amateur bodge job that would still need a professional to get it right).