Flywheel weight
Flywheel weight
Author
Discussion

blitzracing

Original Poster:

6,422 posts

251 months

Wednesday 1st April 2009
quotequote all
Anyone know why reducing the flywheel mass is never mentioned as a tuning aid on these engines ? Although it does not produce any more power, it stops the engine wasting power spinning up the mass of a small planet, especially in the lower gears when the engine spins up faster? Ive seen Alumninum ones for silly money, but surely simply cutting mass from the standard one and rebalancing whould be a good start, especially on a lightweight car like the TVR. I used to remove 3/4 of the wieght on the little 650 cc Fiat Blitz racers I used to build, and never found a downside to it (mind you a LOT less horsepower to play with!).

Mark

spend

12,581 posts

282 months

Wednesday 1st April 2009
quotequote all
Do you believe that TVR flywheels are the same as LR's. Do you believe that all TVR RV8's came with the same flywheels? Do you even have a TVR engine & driveline in your particular car?

If you want to lighten it, all well & good, just decide how much is safe, then re-balance afterwards, job-done.

JonathanT

880 posts

315 months

Wednesday 1st April 2009
quotequote all
I thought that the TVR Rover V8s came with "lighter" flywheels so that if you lightened them further you'd start affecting low rev driveability?

Al 450

1,390 posts

252 months

Wednesday 1st April 2009
quotequote all
When my 4.6 was rebuilt it had a standard Range Rover flywheel. I had it balanced and lightened at John Eales, they took 3 kilos off it!

Much nicer to drive now!

blitzracing

Original Poster:

6,422 posts

251 months

Wednesday 1st April 2009
quotequote all
spend said:
Do you believe that TVR flywheels are the same as LR's. Do you believe that all TVR RV8's came with the same flywheels? Do you even have a TVR engine & driveline in your particular car?

If you want to lighten it, all well & good, just decide how much is safe, then re-balance afterwards, job-done.
No Im running a Rangie Flywheel in all its massive glory in an 850kg car, and of course its not a "TVR" engine, its a modified Range Rover one, as they all are.whistle It was sourced through TVR power origionaly should that make a difference, but unmodified. I found no mention of flywheels in the David Hardcastle book so I wondered if there was a strange reason for not lightening them, like damping crank harmonics or something, but obviously not. Id be interested in seeing a picture of what TVR do if anyone has one.

Thanks

Mark

daz the plumber

14,997 posts

262 months

Wednesday 1st April 2009
quotequote all
i thought reducing the weight of the flywheel will make the tick over lumpy.i had my fly wheel lightened by 6lbs , pistons weighed and drilled ,conrods weighed and balanced and the crank fitted to a balancing machine with the clutch etc fitted .the whole lot cost me £125, it did make a difference revs up to 7000rpm but tick over is slightly lumpy but it was for my mgb 1860 engine .with the head and cam increased the bhp from 70 to 110. i would say all this would improve the v8 engine .done at fardon motors newark .

Al 450

1,390 posts

252 months

Wednesday 1st April 2009
quotequote all
blitzracing said:
spend said:
Do you believe that TVR flywheels are the same as LR's. Do you believe that all TVR RV8's came with the same flywheels? Do you even have a TVR engine & driveline in your particular car?

If you want to lighten it, all well & good, just decide how much is safe, then re-balance afterwards, job-done.
No Im running a Rangie Flywheel in all its massive glory in an 850kg car, and of course its not a "TVR" engine, its a modified Range Rover one, as they all are.whistle It was sourced through TVR power origionaly should that make a difference, but unmodified. I found no mention of flywheels in the David Hardcastle book so I wondered if there was a strange reason for not lightening them, like damping crank harmonics or something, but obviously not. Id be interested in seeing a picture of what TVR do if anyone has one.

Thanks

Mark
I don't think TVR do/did anything to it. The only function is to keep the engine ticking over when declutched and to keep some momentum in the drivetrain when the clutch is engaged although obviously this would be a function of all the rotating mass of the engine, prop, clutch, gearbox shaft, flywheel etc. The amount of momentum required would be proportionate to the mass of the vehicle being moved so assuming a TVR would weigh significantly less than a Rangie I would say it's a safe bet that a lot could be machined off.

I find that I experience far less shunting now at low speed/low revs than before and the engine seems to rev better when declutched e.g. when blipping the throttle on downshifts. I can't comment on power as the work was done in conjunction with a bunch of other stuff.

Chassis 33

6,194 posts

313 months

Wednesday 1st April 2009
quotequote all
spend said:
If you want to lighten it, all well & good, just decide how much is safe, then re-balance afterwards, job-done.
So er...will the bellhousing contain an exploding flywheel or not? I've seen bust tests done on aircraft engines and theyre scary but then again the rev at much more than an RV8 and damage is proportional to the square of speed...
Regards
Iain

900T-R

20,406 posts

288 months

Wednesday 1st April 2009
quotequote all
My flywheel was lightened and balanced as a matter of course with the engine rebuild - not sure by how much. Hasn't noticably impacted idle and take-off, but blip the throttle in neutral and it heads for 6K+ in the blink of an eye. But of course this is on a revvy pre-serp 430. wink

Mr Haribo

318 posts

220 months

Wednesday 1st April 2009
quotequote all
I would be up for a reasonable priced flywheel ? what about alloy front pulleys ect ?

Al 450

1,390 posts

252 months

Wednesday 1st April 2009
quotequote all
Mr Haribo said:
I would be up for a reasonable priced flywheel ? what about alloy front pulleys ect ?
There's no need to lighten anything else like pulleys, just take a little more off the flywheel.

Mr Haribo

318 posts

220 months

Wednesday 1st April 2009
quotequote all
Going slightly off subject, does any do a dry sump kit as i have heard this gives more horses.
And as the flywheel, its not mentioned about gains ect ?

Pupp

13,043 posts

303 months

Wednesday 1st April 2009
quotequote all
The flywheel as fitted to 500 TVRs weighs about 19lb compared to 21 for a 400, which is a derivative of the Rover 2wd unit. There is a gotcha in that 500s were balanced as a built unit (ie with clutch, flywheel, crank and pulley all assembled). Balancing is contentious wink

Chassis 33

6,194 posts

313 months

Wednesday 1st April 2009
quotequote all
It goes a bit off at a tangent, but I did weigh a selection of RV8 flywheels a couple of months ago.
http://www.pistonheads.com/gassing/topic.asp?h=0&a...

Regards
Iain

spitfire4v8

4,025 posts

212 months

Wednesday 1st April 2009
quotequote all
The flywheel on my 4 litre tvr engine is very heavy, the flywheel on my 5 litre tvr engine is cored out on the rear face and considerably lighter. TVR built them the wrong way around hehe

blueg33

47,012 posts

255 months

Thursday 2nd April 2009
quotequote all
spend said:
Do you believe that TVR flywheels are the same as LR's. Do you believe that all TVR RV8's came with the same flywheels? Do you even have a TVR engine & driveline in your particular car?

If you want to lighten it, all well & good, just decide how much is safe, then re-balance afterwards, job-done.
I am not quite sure what you think the differences may be. Engine is an Rv8 supplied by TVR power running thru an LT77 gear box, to a proper limited slip diff, so the driveline is much the same. The only difference is that Marks car is lighter than a typical chim.

rev-erend

21,624 posts

315 months

Thursday 2nd April 2009
quotequote all
Mine weighs 17lbs..

350Matt

3,914 posts

310 months

Thursday 2nd April 2009
quotequote all
I whittled mine down to 14lb then did 80K on it