Just died
Author
Discussion

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
Driving the car this morning in London, traffic moving fairly swiftly, then engine cuts out, drift to side of road, stop, try restarting and she fires into life straight away. Drive another 200m and engine cuts out again, same as before, go to restart and fires first time. Another 200m and she dies, this time for good. Engine turns over, but no hint of firing.

Can hear fuel pump priming, and checked fuel is pressurising.
Engine turns over so can't be imobiliser?
Virtually entire ignition system was renewed about 1000 miles ago, so new arm, cap, plugs, coil, leads extenders etc.

Anyone any ideas?


fredf

267 posts

264 months

Thursday 2nd April 2009
quotequote all
Mind did that to me one evening, one of the wires leading to the coil was falling off

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
fredf said:
Mind did that to me one evening, one of the wires leading to the coil was falling off
Did think about the coil, and did check the leads were secure, they seemed fine, and the Bosch coil is virtually brand new. Maybe the coil's a duffer?

That Daddy

19,466 posts

252 months

Thursday 2nd April 2009
quotequote all
Check the spade male/female connectors in front of the plenum chamber are clean they are tied to the fat loom, mine would not restart when hot random,basically if the switching signal is not sensed from the coil to the ECU then the injectors will not pulse it thinks the engine is not running(you still have spark and fuel pressure to the rail)may not be your problem but worth a try wink

Edited by That Daddy on Thursday 2nd April 13:08

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
That Daddy said:
Check the spade male/female connectors in front of the plenum chamber are clean they are tied to the fat loom, mine would not restart when hot random,basically if the switching signal is not sensed from the coil to the ECU then the injectors will not pulse it thinks the engine is not running(you still have spark and fuel pressure to the rail)may not be your problem but worth a try wink

Edited by That Daddy on Thursday 2nd April 13:08
Thanks, will give that a go.

Would these spades be the ones by the ignition amp / coil etc? or others, or just all?

That Daddy

19,466 posts

252 months

Thursday 2nd April 2009
quotequote all
Teetertank said:
That Daddy said:
Check the spade male/female connectors in front of the plenum chamber are clean they are tied to the fat loom, mine would not restart when hot random,basically if the switching signal is not sensed from the coil to the ECU then the injectors will not pulse it thinks the engine is not running(you still have spark and fuel pressure to the rail)may not be your problem but worth a try wink

Edited by That Daddy on Thursday 2nd April 13:08
Thanks, will give that a go.

Would these spades be the ones by the ignition amp / coil etc? or others, or just all?
As you look from the front of the engine they are about 3" to the right of the coil,the spades plug into little blocks/diodes x2 mine had turned green inside but was tight frown i have never had the same thing happen since cleaning and some maplins silicone grease wink

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
Ok car is now being looked at.

Apparently there is no power on pin 15 of ECU, which should be permanent live - according to Landrover wiring diagram.

Is Chimaera fuse box different to Landrover? Car is P reg 5ltr.

Anyone have a wiring diagram to hand that they could advise or send through?

That Daddy

19,466 posts

252 months

Thursday 2nd April 2009
quotequote all
Have you checked the fuse off the car and the socket,you can sometimes miss a blown fuse unless its removed from the board,cant comment on what fuse powers what at the moment because i am at work and all my info is at home,sorry cant me much more help frown maybe someone will be along soon with the correct info wink have you tried swapping over the 2 silver power relays?





Edited by That Daddy on Thursday 2nd April 18:32

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
Thanks to all.

She's working again now.

Was loose connector in cable linking battery to ECU.

That Daddy

19,466 posts

252 months

Thursday 2nd April 2009
quotequote all
Well done wink

Chimjunkie

2,879 posts

242 months

Thursday 2nd April 2009
quotequote all
weeping I do love a happy ending. Sniffle.

That Daddy

19,466 posts

252 months

Thursday 2nd April 2009
quotequote all
Chimjunkie said:
weeping I do love a happy ending. Sniffle.
Poof hehe only made that remark cos i am jealous of your Chims interior frown

Edited by That Daddy on Thursday 2nd April 21:10

Chimjunkie

2,879 posts

242 months

Thursday 2nd April 2009
quotequote all
That Daddy said:
Chimjunkie said:
weeping I do love a happy ending. Sniffle.
Poof hehe only made that remark cos i am jealous of your Chims interior frown

Edited by That Daddy on Thursday 2nd April 21:10
hehe