Swirl pot damage - anyone else have this?
Swirl pot damage - anyone else have this?
Author
Discussion

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
Just before Christmas, my swirl pot sprung a leak underneath the top neck. I couldn't understand what had caused it as it looked like it had been hacksawed across in a perfectly straight line. I sent it away to be welded up, and it has been fine since, but on inspection today, it has been damaged again in exactly the same place. The damage isn't enough to have punctured the pipe, but it must be nearly through.

The damage must be being caused by the alternator pully grinding on the neck of the swirl pot as the engine tiilts when being reved, but when looking at the position of the pully compared to the neck of the swirl pot (at idle)- it must be 40 odd mm away. Should the engine really be moving this much? Has anyone else had this problem?

Engine mounts were replaced shortly before I bought the car. Could they be in wrong?




pwd95

8,459 posts

269 months

Thursday 2nd April 2009
quotequote all
Engine mounts probably gone again. yes
My engine mounts were changed 12 months before I bough the car & within 7-8 months the exact same thing happened to mine. I'll be using the uprated ones from SC Power next time.

Chimjunkie

2,879 posts

242 months

Thursday 2nd April 2009
quotequote all
Definately engine mounts. The engine is rotating and the power steering pulley is cutting the pipe! Happened to me when one of my engine mounts ripped.

daz the plumber

14,997 posts

262 months

Thursday 2nd April 2009
quotequote all
have you tried fitting the restraint brackets ?ive fitted these ,stop some of the movement .got mine from rpi but many v8 specialists stock them
http://www.sc-power.co.uk/SC%20Power%20Engine%20Mo...

Teetertank

Original Poster:

358 posts

218 months

Thursday 2nd April 2009
quotequote all
daz the plumber said:
have you tried fitting the restraint brackets ?ive fitted these ,stop some of the movement .got mine from rpi but many v8 specialists stock them
http://www.sc-power.co.uk/SC%20Power%20Engine%20Mo...
Not tried. But if they work and the rubber mounts aren't completely shot then seems these restraints are a cheaper alternative. Thanks for the tip. Will check at weekend.

Actually looking back through the history, looks as though they were last done 5 years ago, so probably time for a change...

Is it a big job doing the engine mounts, and are they TVR specific?


daz the plumber

14,997 posts

262 months

Thursday 2nd April 2009
quotequote all
the engine mounts fit inside the restraints, you need to jack the engine up, i would say its a bit tricky .good luck

Chimjunkie

2,879 posts

242 months

Thursday 2nd April 2009
quotequote all
Very straight forward job for any competant DIY mechanic. Best done with both front wheels off. Be careful when supporting engine with jack not to damage sump.

VictorMeldrew

8,293 posts

308 months

Wednesday 8th April 2009
quotequote all
Definately engine mounts. The one on the passenger side is sandwiched between exhaust and manifold, and if the replacement was of the dodgy variety it may well have melted. Mine is now wrapped in heat shielding, well worth doing when you replace the mount.

Simon Says

19,466 posts

252 months

Wednesday 8th April 2009
quotequote all
pwd95 said:
Engine mounts probably gone again. yes
My engine mounts were changed 12 months before I bough the car & within 7-8 months the exact same thing happened to mine. I'll be using the uprated ones from SC Power next time.
yes I have the SC ones(reds)but my replacements for the originals previous to the SC's lasted about 6k bloody waste of money,pattern obviously as we know the originals are no longer available.