Super Charger
Super Charger
Author
Discussion

TVRBOB1998

Original Poster:

32 posts

211 months

Tuesday 7th April 2009
quotequote all
Hi Everyone

I am a Piston Heads virgin so be gentle with me to start!

I have a modified TVR Chimaera 4.8L made in 1998 which I have had since new.

I am looking at various mods but the ultimate will be the Super Charger. My question is- Is the power limited in anyway? I ask because if I was looking at Clive's new manifolds or some form of up-rated air intake is this a waste of time when the engine is at its limit with the SC?

Thanks in advance for your help.
Bob

chrispitman

742 posts

285 months

Tuesday 7th April 2009
quotequote all
The general limit seems to be around 400 BHP much over that it becomes very expensive, pistons, rods etc need uprating and then you have to look at gearbox/diff etc.

450Nick

4,027 posts

243 months

Tuesday 7th April 2009
quotequote all
Hi Bob, I'm sure someone with a bit more technical knowledge with come along and offer a better view soon, but here's mine:

I already run a 4.6 supercharger setup and have about 410bhp/430 torque. I know of a few 5.0, 5.1, 5.2 and 5.3 supercharged engines in build and I think the most that these are looking at are around 500bhp on a single centrifugal charger (SC Power's kit). I understand that a twin supercharger setup in this format could push upwards of 600bhp but obviously a hell of a lot of work and cost would be involved to make this workable.

I think the optimum size for a charged Rover V8 was worked out by John Eales at 5.125 litres, though I have to say that all of the 4.6's I've seen have made very good numbers and on that basis, you should be set up for somewhere around 440/450bhp depending on several variables. The requirements for a charged engine are vastly different to those for an N/A engine however. I'm assuming that on your 4.8, you are running good power already and with this engine, you may already have a hot cam and higher compression in order to make good numbers. Both of these would have to be changed prior to supercharging as the cam requirements are very different, and the motor wants to run lower compression if possible. The intake becomes less important as you are forcing in air, so I have been advised that enlarging the inlet manifold/throttle bodies and the usual N/A favorites will have very little effect on my power output for the cost. It's not that the engine is on its limit, but that the air is being pushed in, so conventional resonant tuning and standard mods have much less of an effect. Exhaust wise, you just need to get the air out as quick as possible. A standard exhaust works great, though I would bet that Clive's manifolds won't fit the charger setup due to the charger bracket limiting clearance. I worked with ACT when fitting my kit and a new aftermarket exhaust based on a blend between the standard system and ACT's performance manifolds was made to suit the system with a slightly larger bore pipe which probably helps the engine breathe, though this hasn't been confirmed with dyno numbers.

Regarding a ceiling however, I think it just depends how much air and fuel you can get in there and whether or not you can contain the resulting bang. On uprated 450 engines though, the bhp seems to come out in the same ballpark of 400-430 bhp with only the torque varying by much as you push to a 5L. This will obviously increase if you can run you motor past 6k revs as Colin Harvey is aiming to do. I think your best bet is to give SC-Power a call and see what is possible on your setup, but I would recommend it as the best and most driveable power mod out there.

Edited by 450Nick on Tuesday 7th April 15:46


Edited by 450Nick on Tuesday 7th April 20:14

450Nick

4,027 posts

243 months

Tuesday 7th April 2009
quotequote all
Just noticed that you're based in Nuneaton. I'm usually based in Central Birmingham and will be back up there next week. If you want to come and have a look at the SC-Power setup and compare the feel of the car to your own then you're welcome to come up for a chat if it will help!

TVRBOB1998

Original Poster:

32 posts

211 months

Tuesday 7th April 2009
quotequote all
Hi 450Nick

Thanks for your great response. Its pretty much answered my questions and it would be great to meet up to see your setup. Since my partner left me I have more time and more money!

Answering both you and Chrispitman I have a 218 cam and up-rated Omega forged pistons, balanced crank, cylinder head, inlet and trumpet base porting and conrods to suit, etc. This was all done a few years ago when my engine developed a fault. I am still trying to find out who built the engine as I fell out with the garage I was dealing with. Now that Dom at TVR Power is looking after it, it runs great. The engine apparently produced 303bhp on the test table and I have figures from Dom when he remapped it but I cant quite remember its output now.

I think my next mod is going to be the engine management system and I am really edging towards DTA.

So let me know Nick when your up my way and I’ll pop over.

Cheers
Bob

Mark Adams

358 posts

291 months

Sunday 10th May 2009
quotequote all
A very nice 450 S/C went out of TVR Power a couple of weeks ago. I can't say too much about without the client's permission, but Dom will be able to give you more specific details (it is the most powerful one ever tested there).

It is on 14CUX, which has a power ceiling of around 470BHP at present. Hopefully this car will get Omex ignition management later as the icing on the cake.

Save your money for the supercharger first!

dhf

1,103 posts

225 months

Sunday 10th May 2009
quotequote all
I have a 5 litre which is currently being rebuilt ready for an SC Blower to be fitted.basically the cc has been increased,compression decreased and a Blower cam fitted(tame)and a few other mods to strenghten the engine on the advice of SC power.aimed for power output 420/420 bhp/lbs torque give or take.will be removing the ACT twin plenum as it is not compatable with the Blower.SC will normally recommend about 380bhp.going higher is really down to the condition of the engine.i was lucky in many ways,Mark Adams on a rolling road session found that my cam was starting to go hence the above,more cost but at least my engine is fully checked over/ set up for the Blower.would probably have blamed the Blower for the cam if MA hadn't found it in time.
Talk to Colin at SC power,very helpful,take a test drive,you will be impressed ! and importantly talk to Mark Adams who is the Rover V8 Guru who sets most of the Blowers up,a mine of info.

Edited by dhf on Sunday 10th May 22:40

GreenV8S

31,027 posts

315 months

Sunday 10th May 2009
quotequote all
Mark Adams said:
It is on 14CUX, which has a power ceiling of around 470BHP at present. Hopefully this car will get Omex ignition management later as the icing on the cake.
Does that mean it got 470 BHP without boost retard?

pOLICE5

1 posts

210 months

Monday 11th May 2009
quotequote all
Hi Mark

I think you are probably talking about my car? (Shaun)

Feel free to talk about stats etc at your Leisure you will do it more justice than me!

Car currently back in at TVR Power after consuming 5th Gear @ Bruntingthorpe last week.

We had a great shakedown and she was in a class of her own compaired with all others on track.

The power delivery is silky smooth with a progressive delivery and with the new set of Nitrons and Willwood brakes she was a dream to drive.

Looking forward to getting the icing on the cake : )

Anyone thinking of going with the SC, just go for it but make sure you upgrade brakes and shocks at the same time!

Mark Adams

358 posts

291 months

Monday 11th May 2009
quotequote all
Indeed it is your car Shaun. It will be interesting to see what the Omex 200 does for an already monstrous motor!

Sorry to say Peter, but it didn't get 470BHP although it is firmly the right side of 400BHP. It is currently using the trusty distributor, but after a quick chat with Shaun today it will be getting the Omex 200 ignition management system to complement the sophisticated 14CUX fuelling asap.

There is a twin turbo 4.0 Litre Range Rover on 14CUX with Omex 150 ignition management that has touched 500BHP, and I know that is just beyond the limit. It was set up at 400BHP, but the owner wound up the boost (against my advice) to see what it would do. It really flies, and has not blown up yet!

Oh yes - and he tows a caravan with it too. He loves seeing off many eurobox "sports cars" with a caravan on the back, although his wife reports it plays hell with the crockery!

TVR Power never quote flywheel figures from their dyno, although it can calculate them. I believe they don't want to get caught in the usual boring BHP bun fight that has spoilt many threads before.

Don1

16,887 posts

239 months

Monday 11th May 2009
quotequote all
Mark Adams said:
Oh yes - and he tows a caravan with it too. He loves seeing off many eurobox "sports cars" with a caravan on the back, although his wife reports it plays hell with the crockery!
biggrin Good man! Get him over here!

Bluebottle

3,498 posts

271 months

Monday 11th May 2009
quotequote all
Mark Adams said:
...Sorry to say Peter, but it didn't get 470BHP although it is firmly the right side of 400BHP...
Phew! I was about to get onto the phone to you mate!

TVRBOB1998

Original Poster:

32 posts

211 months

Tuesday 12th May 2009
quotequote all
Hi Everyone

I've not looked for a while then saw the thread had continued, thanks.

I have heard that 5th gear wont take a great deal of torque since its not secured on and is more or less free. I dont know a huge amount but picking things up as I go. Is this true? Is it something that will pose a problem with SC setups? I have also been told the piston heads need to be flat for a SC?

Thanks
Bob


Boosted LS1

21,200 posts

291 months

Tuesday 12th May 2009
quotequote all
^ Piston crowns need to be bowled to achieve the compression required (hence custom forgings for the pistons). A flat top piston on a 5.0 will make for very high compression normally aspirated let alone under boost. My blown 5.1 had to use bowled pistons to get down to a lowered compression allowing some decent boost. When I built a blown 5.4 I had to use bowled pistons in conjunction with buick 300 heads with big combustion chambers. Even then compression was still very high but the engine was never going to be a revver with the stroke I used. It was intended for a low boost s/c installation.

I'm not sure about the 5th gear aspect but doubt it would really be an issue on a road car where the lower gears get the hammering.

TVRBOB1998

Original Poster:

32 posts

211 months

Tuesday 12th May 2009
quotequote all
Thanks for that Mike. Everyone seems to have different ideas so its difficult knowing what to do and what is true. The same (well known) guy that told me about the pistons told me about the gearbox and with Shaun eating 5th gear it seemed to validate his thoughts.

dhf

1,103 posts

225 months

Tuesday 12th May 2009
quotequote all
Thats why SC power like to stop at about 380bhp as they advise that the gearbox potentially becomes a consumable after that.5th is the weak link as it was an add on gear.Quaif do an upgrade for the box so my attitude is drive on,it may never happen,Cerberas have the same box don't forget.alot i would quess depends on driving style.

Boosted LS1

21,200 posts

291 months

Tuesday 12th May 2009
quotequote all
TVRBOB1998 said:
Thanks for that Mike. Everyone seems to have different ideas so its difficult knowing what to do and what is true. The same (well known) guy that told me about the pistons told me about the gearbox and with Shaun eating 5th gear it seemed to validate his thoughts.
When I last used my turbocharged TR8 it had a 2.84 diff ratio and an lt77 gearbox rebuilt by Ken Tomlinson. I never damaged anything in the transmission/driveline but this may have been because it would break traction instead. I did treat the mechanicals with some sympathy, I always do. A friend had a similar specced car/engine but with a 3.09 diff. He always hammered his car and used several gearboxes but it was the lower gears that broke or he was using the lower gears at the time when something in the box broke.

As for the pistons, flat tops, dished or bowls work quite well. Domed are prety awful but again this depends on head chamber design. You wouldn't want a domed piston in a rover engine.

Edited by Boosted LS1 on Wednesday 13th May 08:27

hiltonig

3,153 posts

239 months

Wednesday 13th May 2009
quotequote all
questions why fit the omex ignition and not go the full hog and fit the omex 700 and ditch the 14cux ???

TVRBOB1998

Original Poster:

32 posts

211 months

Wednesday 13th May 2009
quotequote all
Not a bad question 'why not go the whole hog to Omex 700'. I've really had my eye on DTA. Again everyone seems to have their favourite and I am not sure that some peoples objections to Emmerald, Omex, DTA, etc are just bad experiences in the past. All seem to have come on a long way recently along with their user interfaces and manuals. Does anyone have a recent broad range of experience with the ecu variants. These threads on ecu's seem to come up again and again and I still dont know what to do but I have a bit of money to spend!

Bluebottle

3,498 posts

271 months

Wednesday 13th May 2009
quotequote all
TVRBOB1998 said:
Not a bad question 'why not go the whole hog to Omex 700'. I've really had my eye on DTA. Again everyone seems to have their favourite and I am not sure that some peoples objections to Emmerald, Omex, DTA, etc are just bad experiences in the past. All seem to have come on a long way recently along with their user interfaces and manuals. Does anyone have a recent broad range of experience with the ecu variants. These threads on ecu's seem to come up again and again and I still dont know what to do but I have a bit of money to spend!
I would have a chat with Mark Adams, he has a wealth of valuable knowledge thumbup

The 14CUX is actually very good at controlling fueling, and if you're going FI then the perceived restriction of the MAFM is irrelevant. I will be piggybacking mine with an Omex 200 for ignition control later this year to squeaze a few extra ponies out of it evil.
For an Emerald/Omex etc. to control fueling as well as the 14CUX in all weather conditions, you will need knock sensors, barometric sensors etc. otherwise it is relying solely on the theoretical opening position of the butterfly to "guess" what volume of air is going in (if your butterfly linkage gets worn or goes out of line it can't compensate, you will be constantly "fiddling" with you fuel map. And then it becomes an expensive install.