Cooling - Move Number Plate?
Discussion
I know that my N96 4HC Chim has a history of running very warm, especially when it's hot out! So much so that the previous owner use to put the heater on and had a fan override to help control it. Now it's never over heated, and I want to try and avoid that.
I noticed that the number plate is right in the middle of the grill, where I guess all the air go es through to the engine. Would it make sense to move this to the bottom edge of the grill? I'm sure this must improve airflow for the fans......
I'm not at all mechanically minded, so thoughts would be appriciated....
Cheers
PJ
I noticed that the number plate is right in the middle of the grill, where I guess all the air go es through to the engine. Would it make sense to move this to the bottom edge of the grill? I'm sure this must improve airflow for the fans......
I'm not at all mechanically minded, so thoughts would be appriciated....
Cheers
PJ
Aha, something I can at last comment upon from an informed perspective
I had the same issue (4.0, 1995 M). Mine would get to 90 regularly on the move, but fans would kick in and hold it at between 90 and 100 on the gauge but it didn't seem to cool too quickly after moving again. Sitting in traffic was tense.
First thing was to move the number plate to the lower lip. That worked to a degree in that temps stay at 85 on the move, and drop quicker once moving after sitting in a queue. I also added a lower spoiler (used the square section guttering technique) which also lowered temps on the move to between 80 and 85.
Problem is that over the winter temps have been nearer 70 on the move which is too low I feel, so I probably need to create some form of partial grille cover.

I had the same issue (4.0, 1995 M). Mine would get to 90 regularly on the move, but fans would kick in and hold it at between 90 and 100 on the gauge but it didn't seem to cool too quickly after moving again. Sitting in traffic was tense.
First thing was to move the number plate to the lower lip. That worked to a degree in that temps stay at 85 on the move, and drop quicker once moving after sitting in a queue. I also added a lower spoiler (used the square section guttering technique) which also lowered temps on the move to between 80 and 85.
Problem is that over the winter temps have been nearer 70 on the move which is too low I feel, so I probably need to create some form of partial grille cover.
I moved my friend's numberplate down to the bumper on her Chim and it made a significant difference to the running temperature. I would, however, look to see if there is another underlying problem causing the overheating as it should be OK with the plate on the grille. Cure the problem, if possible, not the symptoms!
I very much suspect you would get pulled.
http://www.dvla.gov.uk/media/pdf/leaflets/v796.pdf
On the cooling effect, I have a 98 4.0, and the guage temp sits around 60 on a run, and up to 90 in traffic, with the fans on.
I have heard that the guages are not that accurate, so the advice I was given was, find out what is "normal" for your car and only change things is fhis changes.
http://www.dvla.gov.uk/media/pdf/leaflets/v796.pdf
On the cooling effect, I have a 98 4.0, and the guage temp sits around 60 on a run, and up to 90 in traffic, with the fans on.
I have heard that the guages are not that accurate, so the advice I was given was, find out what is "normal" for your car and only change things is fhis changes.
Here's a link to pics of my number plate. (N1 BGK).
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
It's a smaller than regulation plate (bike plate?) and I've never had any issues with the feds. Temp stays at 80 all the time except on Motorway runs - 70
I guess airflow must be improved seeing as the air filter and radiator are right behind where where a full size plate would be.
Thanks for the replies all. I actually got caught in a really bad traffic jam yesterday evening on the M4 going west bound heading for the M4. The temp gauge gradually increased to around 95, and only cooled down as traffic started to move! 
So I think I'll go ahead and do that, is it just a couple of self tapping screws into the body work then?

So I think I'll go ahead and do that, is it just a couple of self tapping screws into the body work then?

2nd on the small plate. I have a 9x2.5 inch one and have never been stopped. Even gets through MOT's with it. Does help a lot keeping teh temp lower. Could consider getting a fan over ride switch too, as its good to be in control and get some cooling a few minutes before normal cut in temperature if you know you are going to be stuck.
my 97 450 used to get hot very quickly in traffic and also take a while to cool down once on the move. Never overheated but always a but tense watching the temp rise.
I have noticed since having the pre-cats removed that the engine stays a little cooler on the move and it takes a lot longer when sat in traffic to get to the point where the fans cut in. And they seem to run for a shorter period when they do cut in.
I have noticed since having the pre-cats removed that the engine stays a little cooler on the move and it takes a lot longer when sat in traffic to get to the point where the fans cut in. And they seem to run for a shorter period when they do cut in.
JagPJ said:
I know that my N96 4HC Chim has a history of running very warm, especially when it's hot out! So much so that the previous owner use to put the heater on and had a fan override to help control it. Now it's never over heated, and I want to try and avoid that.
I noticed that the number plate is right in the middle of the grill, where I guess all the air go es through to the engine. Would it make sense to move this to the bottom edge of the grill? I'm sure this must improve airflow for the fans......
I'm not at all mechanically minded, so thoughts would be appriciated....
Cheers
PJ
If you go to www.lovelyplates.co.uk they have a range of small size plates......................I noticed that the number plate is right in the middle of the grill, where I guess all the air go es through to the engine. Would it make sense to move this to the bottom edge of the grill? I'm sure this must improve airflow for the fans......
I'm not at all mechanically minded, so thoughts would be appriciated....
Cheers
PJ
Poledriver said:
I moved my friend's numberplate down to the bumper on her Chim and it made a significant difference to the running temperature. I would, however, look to see if there is another underlying problem causing the overheating as it should be OK with the plate on the grille. Cure the problem, if possible, not the symptoms!
Absolutely - you should be checking for stuck thermostats, silted up or leaky rads, duff expansion tank caps / temp sender units / otter switches etc before you start playing around with the number plate location. Overheating is not inevitable in a TVR and certainly not in April, so it's important to make sure you deal with any underlying problem first.Andy
Had the same problem on the Griff 500. Fine on the move but had to nervously watch the gauge in traffic. Tried fitting a slightly smaller front plate with Velcro and keep the original in the boot. On the move temperatures are reduced but it had little effect in traffic. The solution for me was to fit a switch that allows the fans to run at half speed independently of the normal arrangement. That way when in traffic I select half speed fans which seems to keep things under control better. In the event that it does creep over the normal switch threshold the fans switch to full power.
It seems to me there are several issues here. There are actually four temperature sensors on my engine. One ( the otter switch) on the swirl pot that in standard trim runs the fans, one for the ECU, One that TVR fitted for the gauge and another that sits there with nothing connected. Probably the first thing to check is that the gauge and the swirl pot readings are roughly the same as you may be chasing something that is not a problem. It seems far more sensible to me to run the fans based on actual engine temperature rather than the swirl pot temperature which is what you can do if using an after market ECU. Running them constantly at a reduced speed when things are hot seems to get control better than cycling them on and off.
My Rad runs a good few degrees cooler than the swirl pot which I took to indicate an air lock or blockage. However getting the engine warm, turning it off (to stop the punp) and letting the fans run on for a while then restarting the engine quickly brings the temp down so I concluded the rad was flowing OK.
It seems to me there are several issues here. There are actually four temperature sensors on my engine. One ( the otter switch) on the swirl pot that in standard trim runs the fans, one for the ECU, One that TVR fitted for the gauge and another that sits there with nothing connected. Probably the first thing to check is that the gauge and the swirl pot readings are roughly the same as you may be chasing something that is not a problem. It seems far more sensible to me to run the fans based on actual engine temperature rather than the swirl pot temperature which is what you can do if using an after market ECU. Running them constantly at a reduced speed when things are hot seems to get control better than cycling them on and off.
My Rad runs a good few degrees cooler than the swirl pot which I took to indicate an air lock or blockage. However getting the engine warm, turning it off (to stop the punp) and letting the fans run on for a while then restarting the engine quickly brings the temp down so I concluded the rad was flowing OK.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



