Wishbone removal and rust!
Wishbone removal and rust!
Author
Discussion

lewis_sharman

Original Poster:

5,958 posts

222 months

Tuesday 7th April 2009
quotequote all
Have started the removal of my wishbones today for powdercoating and poly bushing. So far have managed the 4 at the rear of the car, and i am quite shocked by the differences between the upper and lower wishbone conditions with regards to rust.

Upper:


Lower:


Car atm:


Chassis porn after cleanup cool


Apologies for the picture quality, were taken on my phone

TJC46

2,199 posts

237 months

Wednesday 8th April 2009
quotequote all
The top wishbone looks new, most of them look like your bottom one unless they are well waxoiled.

FlipFlopGriff

7,144 posts

278 months

Wednesday 8th April 2009
quotequote all
Had new wishbones about 3 years ago on the 500 (Griff) and painted them (2 coats) with POR15. After bieng used every day since they were fitted there isn't a mark on them - I think this speaks volumes. If you wipe the grime off they are still as shiny as the day they were painted. The stuff is a pain to paint with and takes an age to dry but it does what it says on the tin. Adherance is more difficult on new metal, better on shotblasted and pitted metal.
FFG

900T-R

20,406 posts

288 months

Wednesday 8th April 2009
quotequote all
TJC46 said:
The top wishbone looks new, most of them look like your bottom one unless they are well waxoiled.
yes Very likely that your uppers have been replaced at some point.

lewis_sharman

Original Poster:

5,958 posts

222 months

Wednesday 8th April 2009
quotequote all
I hope thats the case . . . save on powdercoating costs tongue out

Will see when i get the others off scratchchin

CCM

3,521 posts

233 months

Wednesday 8th April 2009
quotequote all
mine are off at the moment as well having the bushes replaced.

I guess as I haven't heard from the garage yet then all is going to plan and not causing too much concern.

lewis_sharman

Original Poster:

5,958 posts

222 months

Wednesday 8th April 2009
quotequote all
tbh i doubt that there is much to have a problem with. The tops are only held in by 3 bolts and the lowers by 4, so worst case scenario there would be a seized bolt.

Saying that i have yet to experience the joys of bush removal rolleyes

CCM

3,521 posts

233 months

Wednesday 8th April 2009
quotequote all
well fingers crossed the car will be back sometime tomorrow and good to go for the wet Bank Holiday weekend.

lewis_sharman

Original Poster:

5,958 posts

222 months

Monday 13th April 2009
quotequote all
Well . . .

All of the wisbones and both ARB's are now off.

Took one of the wishbones into work today and with the aid of head engineer, a hydraulic press, a manual press, a full workshop and lots of hammering we have removed . . .





. . . wait for it . . . .




1 bush in 3 hours!!!!

One stinking little bush! mad


And nobody is open so i can't even go and get a bush removal tool made up!

We tried to fashion one from some steam tubing but alas, too weak.


Hopefully we will have more luck tomorrow and get a foolproof technique frown

Chatsworth is looking bleak

Chimjunkie

2,879 posts

242 months

Monday 13th April 2009
quotequote all
It may be worth hacksawing through the bush. once cut right through it will come out easily. Dont tell me that you did not research the amount of work this can sometimes entail hehe Will be well worth it when done. The self satisfaction alone will bring you to buy all your buddies a beer beer

lewis_sharman

Original Poster:

5,958 posts

222 months

Monday 13th April 2009
quotequote all
Haha yes i was aware but it had to be done so ahh well.

This is the only 'big' job that i know need doing to the car and once its all done and set up properly i know i will be happy smile

I'm just a bit gutted that i really can't see it being ready for Chatsworth, but theres always next year