How much torque to turn the crank?
How much torque to turn the crank?
Author
Discussion

CaptDaveRobinson

Original Poster:

42 posts

215 months

Tuesday 7th April 2009
quotequote all
I am in the middle of an engine rebuild at the moment and I am putting the end caps back on with new main bearings. I have checked the clearances with Plastiguage and they are all fine.

There is some binding with the third cap at the moment which I believe is due to interference from the side. I have that out so I currently have caps 1,2,4 and 5 at correct torque. It feels stiff though and though there is no binding; it takes 43 Nm of Torque to turn the crank. Is this right?

I should have checked the feel of the old one before taking it out. I expect Quinny will know the answer to this but wondering if anyone else can help?

350Matt

3,915 posts

310 months

Tuesday 7th April 2009
quotequote all
If that's just the crank with no rods then yes that's too high, I would expect more like 20Nm if not less.

Are you at full torque for the caps? Has the block been line-bored at all?

CaptDaveRobinson

Original Poster:

42 posts

215 months

Tuesday 7th April 2009
quotequote all
Yeah, just the crank on it's own. 70Nm for 1 to 4 and 90Nm for 5. The block is the old one, I am just changing the bearings. What do you suggest I do?

blitzracing

6,422 posts

251 months

Wednesday 8th April 2009
quotequote all
Sound like you have the caps mixed up, as I think they are assembled and bored afterwards, so ech cap is unique to its position. There is quite a big clearance for the oil so no cap should ever physically bind from the side.

350Matt

3,915 posts

310 months

Wednesday 8th April 2009
quotequote all
OK

First thing the plastigauge is only accurate down to 1 thou so you can't trust it around this figure.

Has the crank been re-ground at all?
What size do the crank pins measure up at and is it the same for all and measured in several different places?

Ribol

12,000 posts

289 months

Wednesday 8th April 2009
quotequote all
At the risk of stating the obvious are you sure you have the right bearings, std/not std crank etc?

spend

12,581 posts

282 months

Wednesday 8th April 2009
quotequote all
3 has the different thrust bearings, sure you got the right bearing set. Need taking down with emery on glass quite often anyway? I'd check / set with the crank end float (& I would hazard a guess you don't have any hehe)

CaptDaveRobinson

Original Poster:

42 posts

215 months

Wednesday 8th April 2009
quotequote all
Yes, thanks guys I am sure I have the right bearings on the right caps in the right order. Think I will narrow it down tonight by doing one cap at a time then sanding each one down as needed. had to do the same thing with the Cam bearings as well. Patience Dave, Patience....

Athlon

5,957 posts

237 months

Wednesday 8th April 2009
quotequote all
Be very careful opening up bearings, if you have the right caps in the right place and the correct bearings (std +10 etc) then try fitting the cranck with No1 and 5 torqued up, check the run out with a dial guage to check the crank is straight on N0 3 bearing journal.

Then, fit number 3 cap finger tight only, knoco the crank nose with a soft hammer or wood and hammer, then bar the crank forwards against the engine stand and while the pressure is on torque the cap.

Now check the resistance and see if it has improved, at the same time double check the thrust clearances are the same crank to cap and crank to block, it they are different then repeat above until you have cap centred.

HTH

CaptDaveRobinson

Original Poster:

42 posts

215 months

Wednesday 15th April 2009
quotequote all
Did a sytematic check today of all of the caps and found the crank turning torque to be the following.

Individually

1,2,4 & 5 less than 20 Nm on their own. 3 binds anyway

Pairs

1 & 2 under 30 Nm
1 & 4 took around 40 Nm
1 & 5 under 30 Nm

2 & 4 around 40 Nm
2 & 5 under 30 Nm

4 & 5 under 30 Nm

Threes

1,2 & 5 took 35 Nm
2,4 & 5 took 38 Nm
1,4 & 5 took 34 Nm

Can anyone make sense of this?

350Matt

3,915 posts

310 months

Thursday 16th April 2009
quotequote all
are there any tight 'spots' or is it tight all the way round?

Boosted LS1

21,200 posts

291 months

Friday 17th April 2009
quotequote all
spend said:
3 has the different thrust bearings, sure you got the right bearing set. Need taking down with emery on glass quite often anyway? I'd check / set with the crank end float (& I would hazard a guess you don't have any hehe)
Like Dave says it could be end float related. Also try removing different shells to see what happens. Make sure the caps are mounted in the correct order and the right way round. Look at the shels to see if they have shiney 'pinch' marks on the ends or around the edges. Are the shells in the right way up or upside down?

Whatever you do, do it gently so as not to wipe out a shell or two.

I can spin cranks by hand if they are correct.

Edited by Boosted LS1 on Friday 17th April 00:11