Cleaning the inside of a Bosch candleholder, I mean headlamp
Cleaning the inside of a Bosch candleholder, I mean headlamp
Author
Discussion

Benjaminpalma

Original Poster:

1,214 posts

213 months

Thursday 9th April 2009
quotequote all
I was washing my car just now and noticed that the inside of the headlight glass is filthy. Is there an easy way to get to this to give it a wipe?

Yes, I'm a numpty - but very pleased! - new owner...

Thanks, peeps.

PurpleV8

137 posts

247 months

Thursday 9th April 2009
quotequote all
Hi Ben,

No real easy way I’m afraid!

You can get at the rear of the lens to replace the bulb etc either by reaching around through the grill or some cars have an access hatch cut into the wheel arch. Neither will get you to inside the lens!

To get inside the lens -
Remove headlamp cowl (2 wing nuts on each reached through front grill and sealant at top)
The lenses are fitted into a rubber seal that is Silkaflexed to the body. You may be able to lever the lenses out of the seal without damage or you may end up cutting the sealant to remove.

I put the lens in the dishwasher and they came out like new!

Do not be tempted to try and wipe the reflectors! As soon as you touch them the silver comes off! If they are looking dull order some new ones before you take it apart. If replacing the reflectors you will also need a set of adjustors as they will be corroded and need replacing.

Good luck
PurpleV8

Benjaminpalma

Original Poster:

1,214 posts

213 months

Thursday 9th April 2009
quotequote all
Thanks, Purple.

I like the touch of putting it in the dishwasher rather than just wiping it with a rag and some lighter fluid!!!

Teetertank

358 posts

218 months

Thursday 9th April 2009
quotequote all
I can second what Purple says regarding not touching the mirror surface on the reflectors. I tried polishing mine with some fine polish and the reflective surface came straight off. Must be micro thin plating.

If you are going to clean them, just use a soft cloth and some soap and water or something.

Konrod

912 posts

259 months

Thursday 9th April 2009
quotequote all
If anyone wants them, I took a load of pics last time I changed my reflector - was going to write up for the Chimaera pages but never finished it. Drop me a line if you want them.

J

daz the plumber

14,997 posts

262 months

Thursday 9th April 2009
quotequote all
hi , from what car are the head lights from .are they not sealed beam .i was thinking may be it would be cheap enough to replace them , as ive just replaced mine on the mgb for £25 the pair .

Simon Says

19,466 posts

252 months

Thursday 9th April 2009
quotequote all
daz the plumber said:
hi , from what car are the head lights from .are they not sealed beam .i was thinking may be it would be cheap enough to replace them , as ive just replaced mine on the mgb for £25 the pair .
Scania truck Daz hehe not sealed beam jsu glass & reflector with a H4 Halogen bulb fitment biggrin

Edited by Simon Says on Thursday 9th April 20:58

Benjaminpalma

Original Poster:

1,214 posts

213 months

Thursday 9th April 2009
quotequote all
daz the plumber said:
hi , from what car are the head lights from .are they not sealed beam .i was thinking may be it would be cheap enough to replace them , as ive just replaced mine on the mgb for £25 the pair .
Could be, but that wouldn't allow the dirt and grime in...

gordonsalive

446 posts

218 months

Friday 10th April 2009
quotequote all
As Simon Says says, if they are originals they are definately not sealed beam, be very careful when taking the cowels off, I had to snap the two bolts due to rusting and re-fashion new ones. Once you have them free you lift the cowel upwards and get a very sharp stanley blade underneath the top to cut the sealant, again be careful with the amount of pressure you apply to the cowel or you will break it. My lenses needed the sealant cutting, replace with 'Sikaflex' once completed, good luck!

daz the plumber

14,997 posts

262 months

Friday 10th April 2009
quotequote all
i would throw the lot away and go for the lupo head light conversion .my mate did his in a weekend , he is a joiner so scribing and fine cutting is an every day affair. !