rolling road session
rolling road session
Author
Discussion

scotty_d

Original Poster:

6,795 posts

225 months

Thursday 9th April 2009
quotequote all
I had a rolling road session yesterday just to see how the car is running after a winter of fettling , up grades and a good service and my result was good it is running like a watch i have 186bhp at the rear wheels according to his rollers up from the 182 last year.

Only changed to a smooth bore elbow. The engine has no more to give in its standard state which makes me happy it runs spot on.

Only problem i still think it uses too much fuel on a run(not heavy right foot) i think the cam could have been changed to a wilder one before i owned the car as it is quite shunty for a 400 at low speeds could this affect fuel consumption? And my peak power comes in at above 5500 rpm?
Is this the norm for a 400? Not complaining just curious

Cheers Scotty




Edited by scotty_d on Thursday 9th April 10:33

lotusandy

257 posts

302 months

Thursday 9th April 2009
quotequote all
I recently had my standard 400 on the rollers, it made 177 BHP at the wheels & 229 BHP at the flywheel, so I guess yours is doing very well.
Max power was achieved at 5670 RPM
Did you get a print out of A/F ratio? If so what figures did you get? I am chasing a rich running issue. mine varied between 12 & 11.5 from 2000 to the rev limiter.
Andy

scotty_d

Original Poster:

6,795 posts

225 months

Thursday 9th April 2009
quotequote all
I did not get a print out but i noticed it sitting at 14. somthing as i had a issue with mine being rich last year it was way down at like 8-9 ish the lamda's had no power to them so it ran very rich.

lewis_sharman

5,958 posts

222 months

Thursday 9th April 2009
quotequote all
I can get my readings later is that is any help, but i think mine peaked at 5500rpm?

scotty_d

Original Poster:

6,795 posts

225 months

Thursday 9th April 2009
quotequote all
Seems normal then that peak power is high up rev band, cool a Excuse to rev it.

Edited by scotty_d on Thursday 9th April 10:50

steve-V8s

2,924 posts

279 months

Thursday 9th April 2009
quotequote all
scotty_d said:
Seems normal then that peak power is high up rev band, cool a Excuse to rev it.

Edited by scotty_d on Thursday 9th April 10:50
Power in BHP is Torque / 5252 X RPM (so torque and power will always be the same at 5252rpm) Where your peak power comes depends on the torque curve.

Simon Says

19,466 posts

252 months

Thursday 9th April 2009
quotequote all
scotty_d said:
I had a rolling road session yesterday just to see how the car is running after a winter of fettling , up grades and a good service and my result was good it is running like a watch i have 186bhp at the rear wheels according to his rollers up from the 182 last year.

Only changed to a smooth bore elbow. The engine has no more to give in its standard state which makes me happy it runs spot on.

Only problem i still think it uses too much fuel on a run(not heavy right foot) i think the cam could have been changed to a wilder one before i owned the car as it is quite shunty for a 400 at low speeds could this affect fuel consumption? And my peak power comes in at above 5500 rpm?
Is this the norm for a 400? Not complaining just curious

Cheers Scotty




Edited by scotty_d on Thursday 9th April 10:33
Scotty,lurching is not necessarily the by product of a spiky cam,some suffer more than others purely on the fact the RV8 runs on the ragged edge air/fuel ratio wise at low RPM,do a search for posts from Blitzracing and you will get a better idea of what's going on and why to cause the dreaded lurch,nice power output by the way thumbup