temp guage
temp guage
Author
Discussion

hillydog

Original Poster:

5 posts

219 months

Saturday 11th April 2009
quotequote all
First posting everyone

Just bought second TVR (First was a wedge), and convinced after 2k miles is a good'n. (Should be, paid strong money for 25k miles model)

Only problem is temp guage rarely goes above 50 degrees, but fan does cut in sometimes

Any suggestions?

sparkesp

298 posts

226 months

Saturday 11th April 2009
quotequote all
I would say its your guage, as the otter switch controls the fans, and when they cut in.
My guage sits around 60 when runnung, but goes to 90 before the fans cut in.
Hope this helps.

V8 Animal

6,015 posts

241 months

Saturday 11th April 2009
quotequote all
hillydog said:
First posting everyone

Just bought second TVR (First was a wedge), and convinced after 2k miles is a good'n. (Should be, paid strong money for 25k miles model)

Only problem is temp guage rarely goes above 50 degrees, but fan does cut in sometimes

Any suggestions?
Sounds like the stat's knackered.

hurststeve

101 posts

230 months

Tuesday 14th April 2009
quotequote all
More likely the temp gauge sender unit I reckon. They do fail in such a way as to give a low temperature reading. I'm just about to change mine for the same reason - hopefully that will be it. Not too easy to get to though, if it's serpentine.

mouseymousey

2,642 posts

268 months

Tuesday 14th April 2009
quotequote all
hurststeve said:
More likely the temp gauge sender unit I reckon. They do fail in such a way as to give a low temperature reading. I'm just about to change mine for the same reason - hopefully that will be it. Not too easy to get to though, if it's serpentine.
I think mine is knackered too. Is it shown in the Bible do you know?


hurststeve

101 posts

230 months

Wednesday 15th April 2009
quotequote all
I don't know off hand, but I expect so. Alternator off to get to it.

debaron

878 posts

228 months

Wednesday 15th April 2009
quotequote all

Dizzy out is the best way to get to the sender unit on the Serp. Mine is also reading low intermittently but the fans cut in now and again regardless of what's on the gauge so will change it.

Simple job - 45 mins.


PAS hose securing clip off (if fitted) - 10 mm ring spanner

14 mm Ring spanner to loosen Dizzy clamp

Twist dizzy when loose to get hand in and remove bolt and clamp

Pull dizzy off - stuff big rag in the hole! Don't want any junk (or water) getting into the engine!

The sender is then right there in front of you. I'd imagine water will come gushing out of the sender hole when removed so make sure you have a rag to stop it getting into the dizzy hole.

New one in and connect up. Dizzy back in and away you go. Obviously pay attention to exactly where the rotor arm is pointing and also mark the dizzy housing against the engine so you can line up when refitting.



Hope this helps!

Ryan


philmccann

430 posts

231 months

Wednesday 15th April 2009
quotequote all
I've just replaced the sender and gauge reads around 50. Going to try with a resistance box to determine the prob. Will let you know.

Cheers

Phil

mouseymousey

2,642 posts

268 months

Wednesday 15th April 2009
quotequote all
Cheers guys, in particular debaron!

My gauge isn't registering anything at all so I'll give this a go at the weekend.

Tyre_Tread

10,697 posts

247 months

Thursday 30th April 2009
quotequote all
mouseymousey said:
Cheers guys, in particular debaron!

My gauge isn't registering anything at all so I'll give this a go at the weekend.
Where did you get the sender from? Part Number?