Balls just mashed a bolt
Balls just mashed a bolt
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Sunday 12th April 2009
quotequote all
I my usall manner smash i used the wrong size spanner and rounded the brass fuel regulator bolt (the FSE one that you plug the gauge into). In my infinate wisdom i then thought i would try the molgrips and have completlty mashed the bolt (i think it was made from cheese).
Any suggestions on how to get the bolt out? theres about 4mm left paperbag


Silent1

19,762 posts

266 months

Sunday 12th April 2009
quotequote all
Hmm, i would usually say weld a nut onto the end of it, but as it's part of the fuel system, that might not be wise.

Meatball

Original Poster:

1,638 posts

241 months

Sunday 12th April 2009
quotequote all
Ive taken the reg off so the petrols not an issue (unless theres any inside) but wouldnt the heat from the welder melt or weaken the diaphram inside frown

Ive got a nasty feeling its going to be another £80 for a new one, unless anyones got a good idea to get it out.

adyw

388 posts

274 months

Sunday 12th April 2009
quotequote all
molegrips redcard

daz the plumber

14,997 posts

262 months

Sunday 12th April 2009
quotequote all
these work and a trip down the plumbers merchant for a new plug
http://cgi.ebay.co.uk/EASY-OUT-OUTS-BROKEN-STUD-SC...

Edited by daz the plumber on Sunday 12th April 21:19

Tyre_Tread

10,697 posts

247 months

Sunday 12th April 2009
quotequote all
daz the plumber said:
these work and a trip down the plumbers merchant for a new plug
http://cgi.ebay.co.uk/EASY-OUT-OUTS-BROKEN-STUD-SC...

Edited by daz the plumber on Sunday 12th April 21:19
Just be careful with those as I had one snap in the bolt I was trying to remove and then it became a battle to get the extractor out before I could get the bolt out. (was a good quality snap-on extractor too so can't blame poor quality extractor)

Edited by Tyre_Tread on Sunday 12th April 23:19

hibutts

38 posts

218 months

Sunday 12th April 2009
quotequote all
If you hsve enough left this is worth a try before using the drill-in type extractor.
http://www.alltoolsdirect.co.uk/draper-12-6-19mm-s...

Alternatively these have got me out of tricky situation:
http://www.kiwiinnovations.com/superwrench.htm

Meatball

Original Poster:

1,638 posts

241 months

Sunday 12th April 2009
quotequote all
Thanks for the ideas chaps...i cant believe i used molgrips on it headache

Barreti

6,689 posts

268 months

Monday 13th April 2009
quotequote all
hibutts said:
If you hsve enough left this is worth a try before using the drill-in type extractor.
http://www.alltoolsdirect.co.uk/draper-12-6-19mm-s...

Alternatively these have got me out of tricky situation:
http://www.kiwiinnovations.com/superwrench.htm
I can recommend the second of these. I have a couple of them and I've managed to use them successfully to get screws out where I've rounded the heads out.

dmmancini

22 posts

212 months

Monday 13th April 2009
quotequote all
Easyouts work great but make sure you have drilled a large enough hole and this will mimize the risk of snapping the tool off. Splined ones are safer but don't work as well. The real bugger is that these easy outs are made extreemly hard so if you snap one off they can't be drilled out and welding to them is a real pain. Good luck.

spend

12,581 posts

282 months

Monday 13th April 2009
quotequote all
Its brass so just stick it in the freezer?

blitzracing

6,422 posts

251 months

Monday 13th April 2009
quotequote all
Good idea Spend- take it one step further and use spray freezer like they do on electrical circuits to freeze the brass locally. You can get the stuff from Maplin.

spend

12,581 posts

282 months

Monday 13th April 2009
quotequote all
I don't suppose you've ever had situations where boiling water works better than a blow torch... Even heat and spot heat have different applications IME;) In this case the even heat (cold) of the freezer is more likely to be effective IMHO. Cleaner, easier and cheaper also ticks the right boxes to boot.

blitzracing

6,422 posts

251 months

Monday 13th April 2009
quotequote all
I guess that will depend on the contraction rate of brass v's the zinc alloy (if thats what it is) if both substances are at the same chill factor.