leaky headlights on chim - any alternatives?
Discussion
Right - Question...
My chim headlights are permanently condensed up, scattering light everywhere. Also all the silver has come off the reflectors.
I've had new headlights fitted at great expense and had them resealed by three different franchised dealers - after just a day they are worse than before and the silver is mostly bubbled.
Please don't suggest repairs or sealants - I want a different light unit, for example a lucas sealed beam unit, although I've been told these don't fit.
So which headlights has anyone found to be a suitable replacement please?
Thanks in anticipation of the customary excellent advice on this forum.
My chim headlights are permanently condensed up, scattering light everywhere. Also all the silver has come off the reflectors.
I've had new headlights fitted at great expense and had them resealed by three different franchised dealers - after just a day they are worse than before and the silver is mostly bubbled.
Please don't suggest repairs or sealants - I want a different light unit, for example a lucas sealed beam unit, although I've been told these don't fit.
So which headlights has anyone found to be a suitable replacement please?
Thanks in anticipation of the customary excellent advice on this forum.
pk500 said:
ripped off!
Not everyone will be comfortable with cutting chunks out of the bodywork of their Chim. I'm fairly handy with a spanner but the bodywork part has me hesitating.I may need to change the headlights on my car as I think the adjusters are corroded and if I do then Lupo lights it will be. Gulp!
Edited by Tyre_Tread on Wednesday 15th April 00:09
Tyre_Tread said:
pk500 said:
ripped off!
Not everyone will be comfortable with cutting chunks out of the bodywork of their Chim. I'm fairly handy with a spanner but the bodywork part has me hesitating.Edited by Tyre_Tread on Wednesday 15th April 00:09
Yeah - good question.
Can anyone who's had their bits cut out (presumably those who sound like they've been breathing helium gas) explain how much or little has been removed and from where?
Is it also a problem that once the removal has taken place, there is no secure attachment for the headlight without glassing in threaded rods and brackets? If that's the case then surely some repainting would be necessary?
I know you can replace the the whole thing with T350 or Tuscan style lights for Carizma price (as opposed to Asda price) but I'd like to keep the original look as far as possible.
Thanks again
Can anyone who's had their bits cut out (presumably those who sound like they've been breathing helium gas) explain how much or little has been removed and from where?
Is it also a problem that once the removal has taken place, there is no secure attachment for the headlight without glassing in threaded rods and brackets? If that's the case then surely some repainting would be necessary?
I know you can replace the the whole thing with T350 or Tuscan style lights for Carizma price (as opposed to Asda price) but I'd like to keep the original look as far as possible.
Thanks again
I can assure you that I did not require any paintwork after I did my conversion. When you have removed the headlamp cowl and all of the headlamp assembly, you will need to remove quite a bit of material, but none of it is normally visible. Basically,the bowl needs to be cut out and the other material needs to be cut back. As a very rough guidline you will probably remove about 10mm from the top lip where the cowl is normally glued, of course, leaving enough to glue it back! the left and right sides you will take to about 5mm from the edge where the visible body work starts. The bottom is the largest chunk,because the headlamps slope forwards, which is probably about 40-50mm from the front edge.
As you may have read in the linked topic above, I fibreglassed some M6 threaded studding to mount the lamps,onto which I welded on some large repair washers on to get a good base for fibreglassing. There are three lugs on the lamp. One at the top, which the studding is mounted vertically up and glassed into the top of the wing. One at the lower front, which the studding mounts horizontally forwards and is glassed above the front indicator and a side lug which points inwards towards the engine. This lug is a little too long and it interferes with the inner bodywork, so it needed cutting back. I glassed in a small bracket tomount this lug.
Before I did any glassing I positioned the lamps, with mounting points and glued the studding/washers and brackets in place with big blobs of Sikaflex. Once dry, the lamps can be removed and the mounts then glassed in to place.
Personally, if I was to do this again, I would talk to mak who had a much simpler way of installation. He simply chopped of the lugs and glued the lamps in to the hole he had created.
Once the lamps are reinstalled you then have to trim the cowls to fit and you will probably have to move the lower wingnut mounting points slightly.
As you may have read in the linked topic above, I fibreglassed some M6 threaded studding to mount the lamps,onto which I welded on some large repair washers on to get a good base for fibreglassing. There are three lugs on the lamp. One at the top, which the studding is mounted vertically up and glassed into the top of the wing. One at the lower front, which the studding mounts horizontally forwards and is glassed above the front indicator and a side lug which points inwards towards the engine. This lug is a little too long and it interferes with the inner bodywork, so it needed cutting back. I glassed in a small bracket tomount this lug.
Before I did any glassing I positioned the lamps, with mounting points and glued the studding/washers and brackets in place with big blobs of Sikaflex. Once dry, the lamps can be removed and the mounts then glassed in to place.
Personally, if I was to do this again, I would talk to mak who had a much simpler way of installation. He simply chopped of the lugs and glued the lamps in to the hole he had created.
Once the lamps are reinstalled you then have to trim the cowls to fit and you will probably have to move the lower wingnut mounting points slightly.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


