ChassisClean treatment
Discussion
Much of the powder coating on my Chimaera outriggers and wishbones has disappeared, having been replaced by surface rust. I've had the car up on stands, and had a really good dig around with a chipping hammer, screwdriver, and bits of bent wire (including on top of the outriggers up inside the tunnels in the body floor) and there doesn't seem to be any through wall penetration or major metal loss. In the longer term I wouldn't be averse to lifting the body and doing a full chassis restoration, but I'd like to keep it going for a few years without any further deterioration. I've read good things in the forum about ChassisClean's treatment in Stoke which looks as if it will cost a reasonable sounding £350ish. Any more views on the process? How long could I expect it to last? Can it be "refreshed" periodically? How much better than DIY Waxoyling is it? The car will do under 3000 miles of mostly summer running as a hobby car. Any advice would be greatly appreciated.
just done mine , firstly get a good heavy duty trolly jack .i then used a angle grinder sounds harsh but it did the job.i jet washed first, then cleaned it down with engine cleaner solution . i used this , works a treat
http://cgi.ebay.co.uk/RUSTBUSTER-EPOXY-MASTIC-car-...
i then sprayed wax oil on the awkward bits.i used 1 litre per side thats for out riggers four wish bones and some of the chassis .
http://cgi.ebay.co.uk/RUSTBUSTER-EPOXY-MASTIC-car-...
i then sprayed wax oil on the awkward bits.i used 1 litre per side thats for out riggers four wish bones and some of the chassis .
I did the same as Daz, except used Dinitrol instead of waxoyl for the final covering. Cannot speak for ChassisClean - like you I've heard good things, but to do mine properly took probably 2.5 weeks solid work for just outriggers/suspension - car was on stands for nearly two months getting pressure-washed, degreased, poked, scrapped, sanded, rust neutralised, painted w/ 2-3 coats of epoxy then dinitrolled. I'm not sure how anyone can be that thorough for a few hundred quid - but maybe someone knows different - how many man hours is their service? Guess they may be much more efficient - they do it for a living after all.
Doing it yourself is an 'orrible job - mostly because of the inaccessible bits ... as you've probably seen. But I'd probably do it again. And probably will when I decide to take the body off
Doing it yourself is an 'orrible job - mostly because of the inaccessible bits ... as you've probably seen. But I'd probably do it again. And probably will when I decide to take the body off

Edited by winters on Tuesday 14th April 20:41
I did mine myself too... dirty job, but at least you know it's done properly... took me 2x full weekends under the car scraping and wire brushing chassis and suspension parts before applying POR15 etch primer, metal ready, and 2x top coats... then a light covering of Waxoyl to finish... that was 2 years ago and had it up on the stands at the weekend and it's as good today as it was when I did it then...
You need to beware of people doing it for a couple of hundred quid, at best this is a wash down, dry and a covering of waxoyl... which might be fine for an A1 chassis, but most aren't A1 and whilst this looks good short term, it hides a multitude of sins beneath.
You need to beware of people doing it for a couple of hundred quid, at best this is a wash down, dry and a covering of waxoyl... which might be fine for an A1 chassis, but most aren't A1 and whilst this looks good short term, it hides a multitude of sins beneath.
Edited by Red V8 on Wednesday 15th April 21:03
Did my outriggers when i 1st purchased the car started by a good powerwash to neutralize any road salt followed by a good drying out then 3hrs + after work over 4 days,primer& POR15 and Dinitrol where i could not reach,but i do have the benefit of a 2 poster ramp
real crap horrible job but had to be done(did i ever say not to get POR15 on your skin
) i dont use the car in the winter but 3 years on its grubby but the paint surface as not been breached,i did the whole engine bay chassis area 18 months ago inc top and bottom tubes, i have still got to do the front wishbones yet and the rear uppers
its not a pretty job and the Dinitrol dues attract road dust but its protected and thats all that matters 
real crap horrible job but had to be done(did i ever say not to get POR15 on your skin
) i dont use the car in the winter but 3 years on its grubby but the paint surface as not been breached,i did the whole engine bay chassis area 18 months ago inc top and bottom tubes, i have still got to do the front wishbones yet and the rear uppers
its not a pretty job and the Dinitrol dues attract road dust but its protected and thats all that matters 
Edited by Simon Says on Tuesday 14th April 22:15
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


