Engine mounts
Engine mounts
Author
Discussion

myquest

Original Poster:

78 posts

258 months

Wednesday 15th April 2009
quotequote all
My 94 400 has knackered mounts, any problems with changing them? Don't have access to a hoist is it easy enough using jacks to lift engine?

penno

241 posts

261 months

Wednesday 15th April 2009
quotequote all
relatively a striaght forward job just a bit tight on space 17mm half moon spanner usfull if I can remember.I used block of wood between a trolley jack and engine sump let the jack take the weight of the engine replaced a side at a time. Takes a bit of messing around to get them in and out jacking the engine up slightly helps


Evo

3,462 posts

285 months

Wednesday 15th April 2009
quotequote all
Just out of interest, can you lift the engine to do the mounts with out it affecting the exhaust, does it put any stress on the manifolds back??

GreenV8S

31,027 posts

315 months

Wednesday 15th April 2009
quotequote all
Evo said:
Just out of interest, can you lift the engine to do the mounts with out it affecting the exhaust, does it put any stress on the manifolds back??
Half an inch here or there should be achievable with the exhaust attached, but I think you'll find you need to separate the rear section from the Y piece to get access to the near side mount anyway.

penno

241 posts

261 months

Wednesday 15th April 2009
quotequote all
I didnt need to remove the exhaust i did the near side twice. I would look at putting the sc power engine mount restraints while your at it. they didn't exist when i did mine next time i will be investing in some.

steve-V8s

2,924 posts

279 months

Wednesday 15th April 2009
quotequote all
17mm ratchet spanner is worth buying to do this job, jack under the sump from the opposite side and it pulls the engine away from the mount a bit. If you cut 2-3mm off the studs before fitting they go in with a lot less bother.

walkie

27 posts

224 months

Wednesday 15th April 2009
quotequote all
I found it much easier to remove the whole assembly not just the mounts alone. The white bracket sits between the mounts and the engine comes off nicely, two 17 and a 13mm bolts to remove.

Simon Says

19,466 posts

252 months

Wednesday 15th April 2009
quotequote all
penno said:
I didnt need to remove the exhaust i did the near side twice. I would look at putting the sc power engine mount restraints while your at it. they didn't exist when i did mine next time i will be investing in some.
yes yep done mine twice too,pattern st ones that did not last very long rolleyes i then fitted the Red SC mounts they tend to be a bit more of a fiddle though,jobs easy enough though smile check the 1/2 bolts that attach the brackets to the block while your at it they can work loose eek

hoach

49 posts

218 months

Thursday 16th April 2009
quotequote all
did this job last weekend.

Axle stands and remove front wheels

There is a 'shim' on the off-side only, dunno why...

lots of WD40 on the threads and undo the inner two nuts first as the outer two bolts will hold it steady.

not difficult.

check under the aluminium swril pot for contact with the pulley 40mm under it?

Seasider

12,728 posts

280 months

Thursday 16th April 2009
quotequote all
hoach said:
check under the aluminium swril pot for contact with the pulley 40mm under it?
yes Was my way of telling mine had gone before i fitted restraints smile

Had moved the swirl pot slightly more central as, i was feed up with getting it welded hehe dont know whether to move it back or not now scratchchin (it restricts dizzy access slightly when moved in board)

rev-erend

21,624 posts

315 months

Thursday 16th April 2009
quotequote all
Here is the link to SC power ..

http://www.sc-power.co.uk/

I bought my mounts from them.