Interesting brake issue
Interesting brake issue
Author
Discussion

rolling_thunder

Original Poster:

152 posts

223 months

Thursday 16th April 2009
quotequote all
It all started when the offside front brake caliper seized on whilst driving - much to the amusement of my passenger when I stopped in a cloud of smoke and ran around like an idiot thinking the car was on fire frown

So i replaced the front calipers and all was fine...

Several months later I have a similar problem in that now the rear brakes do not always release fully and it feels like the handbrake is partially applied (actually if i try the handbreak in this situation it *IS* slightly applied but when the brakes release so does the handbreak)- so.... i replaced the rear calipers thinking i had a dodgy piston... sadly i STILL have the issue dammit.

It seems to occur if I brake fairly hard - given that i have now replaced all the calipers - is it possible that the master cylinder has a 'return' problem? I have never encountered that kind of issue on any previous car.

Cheers

RT

Chassis 33

6,194 posts

313 months

Thursday 16th April 2009
quotequote all
Hi, do you have the problem just on the back axle now? There is a compensator valve type thing (sorry can't be more specific) that sits infront of the inlet to the T for the back axle, have you had a look at this to check there isn't a small bit of grit or a dicky seal stopping it from returning?

Regards
Iain

Simon Says

19,466 posts

252 months

Thursday 16th April 2009
quotequote all
Make sure the Brake switch is not holding the pedal down thus restricting its full return after application,look for anything around the pedal box that may be restricting the brake pedal arms return wink

schmokin1

1,223 posts

243 months

Thursday 16th April 2009
quotequote all
also if you have the original rubber brake hoses check they have not swelled up. When they degrade over time they can swell and block he free access and egress of fluid, retaining a bit of pressure in the system when there should be none.
cheers
schmo

Simon Says

19,466 posts

252 months

Thursday 16th April 2009
quotequote all
schmokin1 said:
also if you have the original rubber brake hoses check they have not swelled up. When they degrade over time they can swell and block he free access and egress of fluid, retaining a bit of pressure in the system when there should be none.
cheers
schmo
They can develop tongues inside the hose too acting like one way valves,where the rubber as de laminated,not seen one of those for a few years now biggrin

occasionaluse

78 posts

239 months

Friday 17th April 2009
quotequote all
Agree with the above - had the same issue - it was definately rubber brake hoses acting like a one way valve

rolling_thunder

Original Poster:

152 posts

223 months

Friday 17th April 2009
quotequote all
Yuh i have seen similar postings before, trouble is I have owned classic cars for a long long time and have never had this problem with collapsing hoses so i dont really understand why TVRs are so prone. Mind you i have never heard of needing to replace calipers after 10 years either.

Guess i'll change all the hoses for braided ones and see what happens - not feeling confident about it though

dhf

1,103 posts

225 months

Friday 17th April 2009
quotequote all
Had a similiar problem in the snow,every time i stopped and then took off the nsr brake was sticking just slightly on so that i took off up the road with more angle than most drifters until it freed itself.it stopped after the snow went.

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
rolling_thunder said:
Yuh i have seen similar postings before, trouble is I have owned classic cars for a long long time and have never had this problem with collapsing hoses so i dont really understand why TVRs are so prone. Mind you i have never heard of needing to replace calipers after 10 years either.

Guess i'll change all the hoses for braided ones and see what happens - not feeling confident about it though
I f your worried about getting air in the system then do one hose at a time and as you remove the union put a rubber cap over the end of the pipe nipple one each brake/corner,keeping the reservoir topped up at all times,this way you can gravity bleed one corner at a time by cracking open that nipple until the air is slowly pushed out,its not the fastest way but you are almost guaranteed not to run into problems,and you can do it single handed,believe me its very easy thumbup even for a laymen,that's not saying you are wink

Edited by Simon Says on Friday 17th April 14:52

rolling_thunder

Original Poster:

152 posts

223 months

Friday 17th April 2009
quotequote all
nah not worried about air - remember i have just changed all the calipers so changing a few hoses is just more of the same - bleeding brakes is pretty easy but I am not a fan of those easybleed systems and prefer a simple tube with a one way valve.

Thanks all - will report back when I have done the hoses

GreenV8S

31,027 posts

315 months

Saturday 18th April 2009
quotequote all
If you suspect the hydraulic is holding pressure then it's easy to find where the problem is. If you crack open the bleed nipple on a calliper, that will release the pressure. If that stops the calliper binding you have confirmed it's a hydraulic issue rather than a sticky calliper. Then do the same thing but this time slacken the joint to the master cylinder instead. If that releases the pressure it confirms the problem is in the master cylinder. There are plenty of faults that can make the m/c hold pressure, including simply having the adjuster done up too tight, or having gunge build up inside that stops the piston from retracting fully. Knowing where the problem is you can then fix it, but don't resort to replacing components just to see whether that fixes it - that's a very slow and expensive approach.