Nitrons ride height
Nitrons ride height
Author
Discussion

hiltonig

Original Poster:

3,153 posts

239 months

Tuesday 21st April 2009
quotequote all
Chaps need some help since having the nitrons fitted the car quite often bottoms out on the bump stops on the rear, inaddition to this the exhaust grounds out in country lanes, I could do with a picture of the rear shocker as mine doesnt seam to have much spring left to compress, Also the heights from the deck to the top of the rear wheel arch would be really usefull, it was set up by a TVR garage not sure if they done it right.

Chimjunkie

2,879 posts

242 months

Tuesday 21st April 2009
quotequote all
Mine did all of the above when i first put them on. Now have ride set back to standard and have about 2 fingers of clearance between rear tyre and arch. The height is simply adjustable by the spring retaining nut. Worth getting everything properly setup by a highly regarded geo place though.

spend

12,581 posts

282 months

Tuesday 21st April 2009
quotequote all
Ask the people who set your car up what ride heights they used, then just reset them back since the springs may just have 'settled'. Plenty of crap springs around ~ they do make a difference wink

450Nick

4,027 posts

243 months

Tuesday 21st April 2009
quotequote all
Make sure it is set high enough... Mine was set low when they were first put on and never bottomed out or crunched the exhaust but it was low enough to prevent the anti-roll bar working. This caused excessive roll on track which I tried and failed to cure by turning up the shocks. Ride height was raised to where it should be and it is now fantastic on track with hugely reduced roll!

hiltonig

Original Poster:

3,153 posts

239 months

Wednesday 22nd April 2009
quotequote all
Chimjunkie said:
Mine did all of the above when i first put them on. Now have ride set back to standard and have about 2 fingers of clearance between rear tyre and arch. The height is simply adjustable by the spring retaining nut. Worth getting everything properly setup by a highly regarded geo place though.
I cannot even get my finder in between the top of the tyre and the flare of the arch, Off to AB shocks then



winston lai

100 posts

252 months

Thursday 23rd April 2009
quotequote all
I have just fitted Nitro with Eibach springs. I have the same problem but only on one or of the rear side (it seems. I am running SP12 18inch rim on my rear. I don't know does it need time to settle but I think I will need to raise the ride height a bit for the time being.

spend

12,581 posts

282 months

Thursday 23rd April 2009
quotequote all
Several of us use 10" springs on the rear with Nitrons wink

It's physically harder to make a strong small spring than a long one & you have much more chance of keeping some pre-load at full droop !

450Nick

4,027 posts

243 months

Thursday 23rd April 2009
quotequote all
The Eibach springs are pre-stressed so should not sink at all. Mine didn't, they were just set too low by the installer. Since being raised up a bit its been great!

hiltonig

Original Poster:

3,153 posts

239 months

Thursday 23rd April 2009
quotequote all
450Nick said:
The Eibach springs are pre-stressed so should not sink at all. Mine didn't, they were just set too low by the installer. Since being raised up a bit its been great!
do you know what spring loading you went for, 500 on the front or 400lb ???

winston lai

100 posts

252 months

Friday 24th April 2009
quotequote all
Did a lot of research and testing on the spring rate before I bought mine from Nitron. The standard recommendation from Nitron is 325lb front and 250lb rear. However, you need to have stiffer springs for a 500 to stop the front end lifting under very hard acceration. The 500 has a lot more torque than the 400. For my likeing. I found an extra 100lb for both the front and rear (425lb front and 350lb rear) are the best for very fast road use. There are no tracks in Hong Kong. However, if you do lots of tarck days then you need even stiffer ones.
After a little teething problem with ride height, they totally transform the handling of the car, especially with some low profile tyres. IOM, money well spent.
Winston