Help me with my shocks please
Help me with my shocks please
Author
Discussion

sapper

Original Poster:

1,134 posts

236 months

Thursday 23rd April 2009
quotequote all
My rear tyres are catching on the body on some B road bumps.
Ive just fitted some Gaz gold shocks to the rear,(the fronts go on tomorrow).
Ive got 25mm of thread showing below the bottom lock nut and the outriggers at the back corners are 150mm off the ground.
Ive wound the setting to 8 clicks clockwise.
What am I doing wrong, and any suggestions for the front please before I fit them tomorrow.

Ive got 17'' wheels all round if that makes a difference.


daz the plumber

14,997 posts

262 months

Thursday 23rd April 2009
quotequote all
i have the standard gaz shockers .i also have 17" wheels .i set the rear ride height at 150mm from the underneath of the triangular plate to the floor .i jacked the car up when winding them to the height then when the car is on the floor twist it up half a turn , when under tension .i have mine set 18 clicks from soft and it`s perfect , they seem to of get better with age .

chrispitman

742 posts

285 months

Friday 24th April 2009
quotequote all
When setting the height you have to keep checking outrigger to ground mesurement as the springs need to settle after you have jacked the car up. Also worth checking you have the right shock and springs on the rear as the rear I think the rear spring should be harder. Also I think the rear should be higher than the front by about 10-15mm do a search on here.

sapper

Original Poster:

1,134 posts

236 months

Friday 24th April 2009
quotequote all
is it just a case of tighten the springs to raise the ride height?

spend

12,581 posts

282 months

Friday 24th April 2009
quotequote all
If you jack it up to do the ride height, you need to roll car up & down to settle the suspension. I would only do that for significant changes. Ramps and a level across them allow you to work under the car whilst the suspension is loaded which is better for fine adjustments IMHO. A proper C spanner to turn the platforms is essential, a good bounce & roll before final check works for me. It's not complicated if you just follow some simple procedures, but if you just jack it, set it you may well find its completely different 10 yards down the drive hehe

sapper

Original Poster:

1,134 posts

236 months

Friday 24th April 2009
quotequote all
Thanks for the tips, best crack on and get it done now.

V8 Animal

6,015 posts

241 months

Friday 24th April 2009
quotequote all
chrispitman said:
When setting the height you have to keep checking outrigger to ground mesurement as the springs need to settle after you have jacked the car up. Also worth checking you have the right shock and springs on the rear as the rear I think the rear spring should be harder. Also I think the rear should be higher than the front by about 10-15mm do a search on here.
I thought the springs should be stiffer on the front 400lb

sapper

Original Poster:

1,134 posts

236 months

Friday 24th April 2009
quotequote all
V8 Animal said:
chrispitman said:
When setting the height you have to keep checking outrigger to ground mesurement as the springs need to settle after you have jacked the car up. Also worth checking you have the right shock and springs on the rear as the rear I think the rear spring should be harder. Also I think the rear should be higher than the front by about 10-15mm do a search on here.
I thought the springs should be stiffer on the front 400lb
I bought them as a kit, from a reputable supplier, so they should be correct.
Its me that doesnt know what he's doing.confused

Ab Shocks

1,686 posts

251 months

Friday 24th April 2009
quotequote all
sapper said:
V8 Animal said:
chrispitman said:
When setting the height you have to keep checking outrigger to ground mesurement as the springs need to settle after you have jacked the car up. Also worth checking you have the right shock and springs on the rear as the rear I think the rear spring should be harder. Also I think the rear should be higher than the front by about 10-15mm do a search on here.
I thought the springs should be stiffer on the front 400lb
I bought them as a kit, from a reputable supplier, so they should be correct.
Its me that doesnt know what he's doing.confused
You are not far off mate but as stated by others, even though our little spring manufacturer in Yorkshire pre-stresses the springs, you still need to allow for some settlement.
I would start off at 42mm from last thread to underside of lockring on the rear and 25mm on the front. about 7-8 clicks from soft on the rear is about right and 5-6 on the front works for me.
Once its all settled down you can arrive at a ride height that works for you.

Oh and yes, 400lb front and 325lb rear.

Edited by Ab Shocks on Friday 24th April 20:47

mongo3528

58 posts

235 months

Friday 24th April 2009
quotequote all
Are those settings 42mm rear and 25mm front the same for the basic Gaz shocks? mines been in bits over winter but am soon to lower the car so the starting settings would be useful thanks .

V8 Animal

6,015 posts

241 months

Friday 24th April 2009
quotequote all
mongo3528 said:
Are those settings 42mm rear and 25mm front the same for the basic Gaz shocks? mines been in bits over winter but am soon to lower the car so the starting settings would be useful thanks .
Yes they will be.

mongo3528

58 posts

235 months

Friday 24th April 2009
quotequote all
THANK YOU !

sapper

Original Poster:

1,134 posts

236 months

Saturday 25th April 2009
quotequote all
Ab Shocks said:
sapper said:
V8 Animal said:
chrispitman said:
When setting the height you have to keep checking outrigger to ground mesurement as the springs need to settle after you have jacked the car up. Also worth checking you have the right shock and springs on the rear as the rear I think the rear spring should be harder. Also I think the rear should be higher than the front by about 10-15mm do a search on here.
I thought the springs should be stiffer on the front 400lb
I bought them as a kit, from a reputable supplier, so they should be correct.
Its me that doesnt know what he's doing.confused
You are not far off mate but as stated by others, even though our little spring manufacturer in Yorkshire pre-stresses the springs, you still need to allow for some settlement.
I would start off at 42mm from last thread to underside of lockring on the rear and 25mm on the front. about 7-8 clicks from soft on the rear is about right and 5-6 on the front works for me.
Once its all settled down you can arrive at a ride height that works for you.

Oh and yes, 400lb front and 325lb rear.

Edited by Ab Shocks on Friday 24th April 20:47
Cheers mate,
Ill go to those settings in the morning and test it out on the way to chatsworth.

haircutmike

22,511 posts

235 months

Sunday 26th April 2009
quotequote all
If your tyres are catching on the arches, it is worthwhile having your camber angles checked.
There is very little play inbetween tyre and arch.
On mine, with different wheels,(18"), the tyres were rubbing when set up to the correct camber angles.
We settled for an additional plus 1/2 degree on the rear and plus 1 degree on the front, (car gets used a fair bit on the track), problem solved.

HCM.

sapper

Original Poster:

1,134 posts

236 months

Monday 27th April 2009
quotequote all
Set up yesterday as advised, and feels great, car is booked in for an alighnment check etc, so thanks for all your help folksclap

Edited by sapper on Monday 27th April 18:45