V8 misfire
V8 misfire
Author
Discussion

sparkypete

Original Poster:

617 posts

234 months

Friday 24th April 2009
quotequote all
I have posted this on this forum hoping for some assistance from a V8 guru.

My V8s appears to have developed an intermittent problem since I put it back on the road after the winter break. It starts and drives perfectly, but every now and then it develops a misfire. I stop turn key off and immediately restart the car and all’s well, no misfire and runs perfectly again, and will do for many miles. I did approx 90 miles last Sunday and the problem surfaced twice, each time starting straight away and off we went again.

I think it could be fuel related as opposed to ignition system, main reason being that the ignition system was all replaced last summer.

The car ran all last year with no problems at all it only appears to be since the season start.

Help

Pete


Chimjunkie

2,879 posts

242 months

Friday 24th April 2009
quotequote all
Were all the ignition parts recognised quality replacements? I say this because there are many cheap parts out there which fail under the heat surprisingly quickly. Just because the parts are new i would not rule out an ignition fault.

sparkypete

Original Poster:

617 posts

234 months

Saturday 25th April 2009
quotequote all
Thanks for the reply, rotor arm is genuine Lucas, has it written on thearm, leads are magnecor, cap is genuine Lucas and coil is also Lucas.

Cant understand why the missfire would go away so quick by just switching off and switching on again. If it was ingnition surely ther fault would still be present as the under bonnet temp will not have reduced any.

What makes me think its fueling is that I had something similar earyl last year and it was rectified by fitting a new Bosch pump.

Bluebottle

3,498 posts

271 months

Saturday 25th April 2009
quotequote all
sparkypete said:
Thanks for the reply, rotor arm is genuine Lucas, has it written on thearm, leads are magnecor, cap is genuine Lucas and coil is also Lucas...
Doesn't necessarily mean its not the cause. I had a rolling road session last week where MA replaced my nearly new rotor arm with a "new" Lucas arm (my cap was 6 months old), two days after RR session i get a misfire...Rotor arm and dizzie cap diagnosed as the fault!
visual inspection of both should show up any signs of arcing.

davvid

38 posts

239 months

Saturday 25th April 2009
quotequote all
I had a problem like that,which got slowly worse until it eventually completely conked out when hot,it turned out to be the ignition amp,which starts to intermittently fail at high engine temps,and I thought at first it was the fuel supply.

GreenV8S

31,027 posts

315 months

Saturday 25th April 2009
quotequote all
It's common for relays that are starting to go to build up contact resistance and not clamp the contacts properly. Perhaps you have a duff relay somewhere that is starting to cause power loss. I would check the main power and fuel pump relays for signs of overheating, if nothing shows up then wire a volt meter up to the fuel pump and see whether the misfire is accompanied by a voltage drop. If that's OK then do the same with the ignition switched feed to the coil.

sparkypete

Original Poster:

617 posts

234 months

Saturday 25th April 2009
quotequote all
Thanks for the advice so far, today I have been checking all the injector connectors, one was quite green with rusty pins, so this has been cleaned up, I will have to see what happens on the run to Chatsworth.

Checked all ingnition for arcing, nothing to see all seems in good order.

Interesting idea Green regarding the conection of a volt meter to the pump, next on list if the issue persist and I have a spare amp so Ill try that whilst I am at it.

We will see tomorrow if I make it to Chatsworth

GreenV8S

31,027 posts

315 months

Saturday 25th April 2009
quotequote all
sparkypete said:
one was quite green with rusty pins, so this has been cleaned up
Check that the seal is still in place on the connector - they're supposed to be weatherproof.

sparkypete

Original Poster:

617 posts

234 months

Saturday 25th April 2009
quotequote all
If I can find some new injector connectors and shrouds I am going to change them all. Anybody any ideas where to find them.

Just as a side point I removed the 2No 30A relays and stripped them down. The contacts were pitted so these have been cleaned up so well see tomorrow.

Thanks all for the suggestions.

Pete

GreenV8S

31,027 posts

315 months

Saturday 25th April 2009
quotequote all
sparkypete said:
If I can find some new injector connectors and shrouds I am going to change them all. Anybody any ideas where to find them.
See "mini power timer" connectors from Vehicle Wiring Products (and various other automotive electrical type places).

sparkypete

Original Poster:

617 posts

234 months

Saturday 25th April 2009
quotequote all
Thanks Green, I have been trying to find these for the last couple of days

Pete

GreenV8S

31,027 posts

315 months

Saturday 25th April 2009
quotequote all
sparkypete said:
Thanks Green, I have been trying to find these for the last couple of days

Pete
Note that the terminals and housings are sold separately. There are two styles of housing.

Junior-Timer:


Junior-Power-Timer:


They both fit, but the 'power' ones are bigger, have a better latch which makes them easier to use - they're more or less identical to the OEM injector plugs.

If you think you might ever need to diagnose engine management problems it's worth getting a couple of spare male/female connectors; with these plus a 12V LED you can make up an injector test lamp that plugs in between the injector and the loom.



chimalsu

279 posts

269 months

Wednesday 29th April 2009
quotequote all
when i had the same sort of problem it turned out to be the fuel filter.when the pump primes the crud is disturbed and blocks the filter,turn off ignition the pressure releases and the crud settles back down.start engine and crud starts building up again.change filter,worked for me.