What are the real benefits of decatting
Discussion
Hi,
Tried searching the forum but could find the right answers. I do know one end of a spanner from the other but would like some help on the actual gains when removing the cats. First of all how many cats are there in a Chimaera and where are they situated (all in the Y piece?).
What do you gain when they are removed?, i know about the downside of MOT time but i can deal with this when the time comes.
What are the rough costs to do this job yourself or is it best left to someone like the very nice David Batty.
Many thanks
Tried searching the forum but could find the right answers. I do know one end of a spanner from the other but would like some help on the actual gains when removing the cats. First of all how many cats are there in a Chimaera and where are they situated (all in the Y piece?).
What do you gain when they are removed?, i know about the downside of MOT time but i can deal with this when the time comes.
What are the rough costs to do this job yourself or is it best left to someone like the very nice David Batty.
Many thanks
You get to save the planet by not pumping out all that globally warming CO2. 
Seriously, there are only two disadvantages to removing the main cat and no disadvantages to removing the pre-cats.
These are MOT test and any problems you have passing it. There are various ways of getting through the test, but his can entail refitting a Y piece with a cat just for the duration of the test, then removing it again.
The other potential disadvantage is noise levels. If you do track days then I can raise your sound level above some tracks’ permitted level.
Your best bet is not to remove the main cat from your Y piece. Buy another Y piece from one of the tuning places like ACT or V8 Enhancements. These will give you more power and you still have the original for MOT time.

Seriously, there are only two disadvantages to removing the main cat and no disadvantages to removing the pre-cats.
These are MOT test and any problems you have passing it. There are various ways of getting through the test, but his can entail refitting a Y piece with a cat just for the duration of the test, then removing it again.
The other potential disadvantage is noise levels. If you do track days then I can raise your sound level above some tracks’ permitted level.
Your best bet is not to remove the main cat from your Y piece. Buy another Y piece from one of the tuning places like ACT or V8 Enhancements. These will give you more power and you still have the original for MOT time.
I've been searching around the posts on here, am i right in saying that the two pre cats are at the end of the manifolds and can be hacked out with some liberal srewdrivering,hammer,chisle etc.
Is this an easy ish job to remove the manifolds and get rid of the precats and will removing them really increase the db noise??
Ive also been looking at aluminised glass cloth to cover the induction pipe into the AFM to cut the air temp down, will this make a noticable difference when the cars at operating temps? Need to source a smooth intake pipe, anyone know where to get this pipe or is it a trip to ACT?
Is this an easy ish job to remove the manifolds and get rid of the precats and will removing them really increase the db noise??
Ive also been looking at aluminised glass cloth to cover the induction pipe into the AFM to cut the air temp down, will this make a noticable difference when the cars at operating temps? Need to source a smooth intake pipe, anyone know where to get this pipe or is it a trip to ACT?
Edited by Evo on Sunday 26th April 22:25
There are 2 Pre Cats in the manifolds,removing these does help the performance very slightly.
Removing the main cat in the Y piece is an option, but you need to check on how the engine will work.
Back Pressure etc and the ECU reading via the lamba sensors needs to be taken into consideration.
Removing all the Cats does help the sound, but you then fall into the changed mods to the car and must declare on insurance.
Also at MOT time you need a Cat in the car to pass and not just the furry kind sitting on the passenger seat!!!!
I have run my Chimaera with the Pre- Cats out for years and it does help the engine and the sound.
Hope this helps, and watch those cats on the passenger seat!!!
Colin L
Removing the main cat in the Y piece is an option, but you need to check on how the engine will work.
Back Pressure etc and the ECU reading via the lamba sensors needs to be taken into consideration.
Removing all the Cats does help the sound, but you then fall into the changed mods to the car and must declare on insurance.
Also at MOT time you need a Cat in the car to pass and not just the furry kind sitting on the passenger seat!!!!
I have run my Chimaera with the Pre- Cats out for years and it does help the engine and the sound.
Hope this helps, and watch those cats on the passenger seat!!!
Colin L
Okay someone has to say it...
There is a legal downside of removing the CATS - the MOT guy is merely enforcing the boring governments ruling that cars post a certain date must be fitted with Cats. So its kinda like running slick tyres all year and swapping them out for treaded ones just for the MOT.
But obviously you are asking about removing the CATS so that you can get more power on the race track
Okay - now i'm gonna run away and hide from all the 'boring person' flak... but at least you know.
Cheers
There is a legal downside of removing the CATS - the MOT guy is merely enforcing the boring governments ruling that cars post a certain date must be fitted with Cats. So its kinda like running slick tyres all year and swapping them out for treaded ones just for the MOT.
But obviously you are asking about removing the CATS so that you can get more power on the race track

Okay - now i'm gonna run away and hide from all the 'boring person' flak... but at least you know.
Cheers
The pre-cats will have no effect on MOT emissions, only the warm up cycle which is part of the manufacturers approval testing 
Pre-cats can be removed by hacking out, you can also change tyres with a hacksaw if you are so inclined
If you cut the precats out, it gives access to the 4-1 joint and you can make sure that is welded up properly - it is the main source of problems with manifolds so I would take the opportunity to have it checked / fixed at the same time. I think you will find that proper exhaust servicers like JP would automatically do it this way. Down side is that you really need someone with a jig to mount both bits in welding back together - and being mixes of mild / stainless.. decent++ welding skills to boot.

Pre-cats can be removed by hacking out, you can also change tyres with a hacksaw if you are so inclined
If you cut the precats out, it gives access to the 4-1 joint and you can make sure that is welded up properly - it is the main source of problems with manifolds so I would take the opportunity to have it checked / fixed at the same time. I think you will find that proper exhaust servicers like JP would automatically do it this way. Down side is that you really need someone with a jig to mount both bits in welding back together - and being mixes of mild / stainless.. decent++ welding skills to boot.Did mine a couple of weeks ago. Sounds better with your foot to the floor but a little more tractor like at idle. I have bought some exhaust wrap just to cover the area that had the pre-cats to see if that will change the sound at idle. The car does feel like it goes a little better.
Some hints – Use a long masonry drill to drill them out it took about 2.5 hours including cleaning. If you cant remove the lambda sensors watch where you drill and be careful I managed OK. Just in case cover the sensors with some decorating tape. You should ware a mask and it’s a good idea to do it outside. Spaying water on the pre-cats is OK to keep the dust down but not on the lambda sensors.
Some hints – Use a long masonry drill to drill them out it took about 2.5 hours including cleaning. If you cant remove the lambda sensors watch where you drill and be careful I managed OK. Just in case cover the sensors with some decorating tape. You should ware a mask and it’s a good idea to do it outside. Spaying water on the pre-cats is OK to keep the dust down but not on the lambda sensors.
rolling_thunder said:
MOT guy is merely enforcing the boring governments ruling that cars post a certain date must be fitted with Cats.
Strictly speaking, it only has to pass an emissions test. There is no explicit test that the cat is present and working. However, you'll find it is exceptionally difficult to pass a 'cat' emissions test without a cat.does anyone know of an idiots guide to removing the precats, can you get the manifolds off without moving the rest of the exhaust back, do they have to be welded once the precats have been hacked out, I'm wondering if this is best left to an expert or can it be done easily diy, i dont have a garage so the hacking out will be done in my shed (with built in music,heater and fridge for the beers)
Come on some one help me with a dumb dumb step by step
Come on some one help me with a dumb dumb step by step

Cutting open the manifolds to remove pre-cats is daft and totally unnecessary
(unless fitting anti reversal cones)once the manifolds are on the bench you are looking at about 1/1.5 hours tops to get them out of both manifolds with a drill & long masonry bit and a long spike,they just break up once you start prodding and poking,please don't breath in the dust(very harmful)and gloves are a recommended
make sure both Lambda probes are removed while work is in progress too 
(unless fitting anti reversal cones)once the manifolds are on the bench you are looking at about 1/1.5 hours tops to get them out of both manifolds with a drill & long masonry bit and a long spike,they just break up once you start prodding and poking,please don't breath in the dust(very harmful)and gloves are a recommended
make sure both Lambda probes are removed while work is in progress too 
Edited by Simon Says on Monday 27th April 15:00
You have to take the Y piece off. There is no reason to take anything downstream of the Y piece off. It's a lot easier if you take the manifolds off the car so you can get at the insieds easily, but that is a pig of a job in itself so leave them on the car unless you already have to take them off for other reasons.
Taking the Y piece off is quick and easy to do and enables you to look at the end of the precats. If they're firmly in place and not obviously blocked consider leaving them as they are until the manifolds have to come off for some other reason. If they're loose or breaking up then best take them out rather than let them come out on their own and damage the lambda sensors and main cat.
If you do take them out with the manifolds in place then remember to run the engine for a few seconds to blow the cr@p out before you refit the Y piece, otherwise all the debris will end up blocking the main cat. Bear in mind that with open manifolds it will be QUITE LOUD and also produce lots of CO, so only run briefly and then leave the area to ventilate for a while.
Taking the Y piece off is quick and easy to do and enables you to look at the end of the precats. If they're firmly in place and not obviously blocked consider leaving them as they are until the manifolds have to come off for some other reason. If they're loose or breaking up then best take them out rather than let them come out on their own and damage the lambda sensors and main cat.
If you do take them out with the manifolds in place then remember to run the engine for a few seconds to blow the cr@p out before you refit the Y piece, otherwise all the debris will end up blocking the main cat. Bear in mind that with open manifolds it will be QUITE LOUD and also produce lots of CO, so only run briefly and then leave the area to ventilate for a while.
Evo said:
Hi,
Tried searching the forum but could find the right answers. I do know one end of a spanner from the other but would like some help on the actual gains when removing the cats. First of all how many cats are there in a Chimaera and where are they situated (all in the Y piece?).
What do you gain when they are removed?, i know about the downside of MOT time but i can deal with this when the time comes.
What are the rough costs to do this job yourself or is it best left to someone like the very nice David Batty.
Many thanks
Tried searching the forum but could find the right answers. I do know one end of a spanner from the other but would like some help on the actual gains when removing the cats. First of all how many cats are there in a Chimaera and where are they situated (all in the Y piece?).
What do you gain when they are removed?, i know about the downside of MOT time but i can deal with this when the time comes.
What are the rough costs to do this job yourself or is it best left to someone like the very nice David Batty.
Many thanks
WOW have you been reading my mind. Thats just what I was going to ask WELL DONE 
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





