induction pipe lagging
induction pipe lagging
Author
Discussion

hodgo

Original Poster:

55 posts

292 months

Sunday 26th April 2009
quotequote all
Afternoon all,

Whats the best material to lag the induction piping with to reflect engine bay heat away to prevent heat soak into the pipes? Currently running the full ACT induction system with a short section supplied with the kit; have seen many heat sleeves / tapes on the web and just wondering what has worked for people here.

Cheers thumbup

debaron

878 posts

228 months

Sunday 26th April 2009
quotequote all
If you're careful and delicate, there's no reason I can see of why Aluminium Kitchen foil wouldn't work. if it was me I'd trial fit the kit first then take the big engine bay pipe off and carefully wrap it in foil, probably double or triple thickness. Then you can tape up the join. If you want to be REALLY particular about it, you can use that Aluminium sellotape stuff to tape the joins. Use the foil shiny side outermost.

As for the plenum elbow, that would be tough to wrap in foil. If you can buy 2 inch Aluminium tape then you could probably do it overlapping, kinda like a Squash racquet grip.

Or maybe there is a heat reflective paint that you could spray on - I guess shiny silver aerosol would be ok, as anything reflective would bounce the Infra Red radiation off. Not sure what it would do to the rubber though. Worth testing on a small sample of pipe first to make sure it doesn't eat holes in it eek

roysum

961 posts

220 months

Sunday 26th April 2009
quotequote all
Using foil tape or kitchen foil would not be that beneficial, you would still get a lot of conducted heat, may even be worse.
I have used foil type fan ducting, at 100mm diameter it actually provides an air gap. pushed right down towards the front I reckon it also picks up a bit of cool air. It can be nicely clamped under the afm clips.
I haven't used it on the elbow yet, but cant see any problems there.

Roy

Badmutha

658 posts

224 months

Sunday 26th April 2009
quotequote all
I did mine with 2 layers of silver ducting tape with a layer of bubble wrap between them, secured with some thin wire loops every 6" or so.It still looks ok after about 5000 miles.HTH

450Nick

4,027 posts

243 months

Sunday 26th April 2009
quotequote all
Tim at ACT sells some proper heat resistant sleeving. Its shiney/aluminium on the surface with a sort of textile weave stuff underneath. You just order a length and slide it over the induction pipe. Well worth it as it brought my inlet temps from 40/50 down to 15/20 (measures in the AFM position).

TJC46

2,199 posts

237 months

Sunday 26th April 2009
quotequote all
Hi guys i work in the insulation industry (industrial,oil refineries,power stations etc) The material most suited is glass cloth. It is available to suit various temps and can come as a plain cloth both sides or as would be ideal for this purpose foil faced on one side. It is a similar material as the glass webbing some use to wrap the exhaust manifold,but obviously a finer weave to give it a cloth feel. The inner wing liners on most TVR"S on view in the engine bay are foil faced glass cloth. Tom.

450Nick

4,027 posts

243 months

Sunday 26th April 2009
quotequote all
TJC46 said:
Hi guys i work in the insulation industry (industrial,oil refineries,power stations etc) The material most suited is glass cloth. It is available to suit various temps and can come as a plain cloth both sides or as would be ideal for this purpose foil faced on one side. It is a similar material as the glass webbing some use to wrap the exhaust manifold,but obviously a finer weave to give it a cloth feel. The inner wing liners on most TVR"S on view in the engine bay are foil faced glass cloth. Tom.
That sounds like the stuff Tim sells, except the two sides are stiched to turn it into a sleeve.

hodgo

Original Poster:

55 posts

292 months

Sunday 26th April 2009
quotequote all
thanks guys.

The best options i've found for the solution are on http://www.autoinparts.com/Heat_Shield_Products-Th... under CIS Cool Intake System & Reflect-a-Sleeve. Will give ACT a call to compare prices. phone

daz the plumber

14,997 posts

262 months

MrChips

3,299 posts

241 months

Tuesday 28th April 2009
quotequote all
I've just bought some for my 450 and for the first time ever, Demon Tweeks turned out to be the cheapest by far!

Got them to make up a 1x2m length for me at £17inc Vat. If you're ordering a few other things at the time then the postage isn't so bad (flat rate per order).

http://www.demon-tweeks.com/products/ProductDetail...