Clutch replacement sob sob
Clutch replacement sob sob
Author
Discussion

phonomenon

Original Poster:

3 posts

211 months

Monday 27th April 2009
quotequote all
Hi all

I have a chimeara 400 & was wondering if anyone could point me in the right direction towards replacing the clutch!! I looked at it many a times and just can decide weather or not to take the engine out, loads of my friends tell me that theres enough room to enable to take the rear shaft off and just slide the box backwards but im not convinced! They make it sound ever so easy & i just know its not going to be, Someone even suggested that the body needs removing! Surely this cant be right??
Any help/advice would be appreciated!! oh by the way i am a competent mechanic but just dont fancy making my life any harder than it needs to be and if i can save myself £1300 which my closest garage quoted it would be a life saver! Times are hard!

J

crackedfinger

1,569 posts

260 months

Monday 27th April 2009
quotequote all
It's cheaper than 1/2 that price for the clutch to be changed form adverts in Sprint - search the forums this topic has been covered lots before.

Simon Says

19,466 posts

252 months

Monday 27th April 2009
quotequote all
The box can come out from underneath with the engine in situ and the body intact,just as per a conventional car,this job as been done by many people on this forum in the same boat as yourself wink

lifebegins@400

217 posts

231 months

Monday 27th April 2009
quotequote all
The box comes off first and then the bellhousing I believe but you certainly don't need to take the engine out - the price you have been quoted is a joke! As per other post you should be looking at £650 all in if you shop around the specialists.

Mad Mitch

842 posts

259 months

Monday 27th April 2009
quotequote all
From my understanding, it can be done from underneath. Simply remove gearbox from belhousing first. Prices seem to be around 450 to 550 inc vat from indies.

phonomenon

Original Poster:

3 posts

211 months

Monday 27th April 2009
quotequote all
Hi

thanks for the info, Its a relief. I too thought that the price i was rather exaggerated but i think as soon as i said its a tvr and that it needed to be recovered the pound signs started apearing in front of there very eyes.

Now for the clutch itself would anyone be able to tell me if i need to buy the clutch direct from tvr or could i get it from some aftermarket place asking for a particular rover clutch

Thanks for all the help!! Its really put a smile on my face

J

Mad Mitch

842 posts

259 months

Monday 27th April 2009
quotequote all
Its a Borg & Beck item but TVR power can supply a quality item.

Steve.

Kitchski

6,552 posts

262 months

Tuesday 28th April 2009
quotequote all
Put a new one in our 400 last year. Clutch was £150 from V8 Developments, and was a reconned AP Racing item.
Local decent garage wanted £150 labour to fit.
Also changed the release arm and pivot (important that you do if it's been worn a long time)

I was gonna do it myself, as some people manage with just axle stands and a jack, but it's too much hassle for £300, and it's not like I'm experienced with the job! But its not an engine out job, or body off (loved that one!) From what I've read, getting the box off isn't that tricky, but its a really really heavy box!

paulathome

686 posts

249 months

Tuesday 28th April 2009
quotequote all
As above it can be done from under the car.
Remove rear anti roll bar,
Remove exhaust,
Remove prop shaft,
Remove gearbox mountings,
Remove reversing light switch connector,
Remove handbrake cable at hand brake end, to allow centre console removal,
Remove centre console and undo gear lever to gear box tube,
Remove slave cylinder and tie back,
Remove gearbox to bell-housing bolts,
Remove gearbox and lower gently to the floor. (don't use head as axle stand like I did)
Remove bell-housing bolts and remove bell-housing.
The clutch is there to see in all is glory, remove and fit new one with new release arm.
Replacement is the reverse of removal. (in Haynes manual speak)
I managed it on the drive took about 12 hours with many brews in the process.
Oh and it rained most of the time furious
Hope this helps and convinces you to pay someone else to do it.
Cheers.
Paul

Edited by paulathome on Tuesday 28th April 18:12

phonomenon

Original Poster:

3 posts

211 months

Tuesday 28th April 2009
quotequote all
Hi

I would like to say a really big thank you for all your imput!! I have decided to have a go at it!!!


Jonathan

Kitchski

6,552 posts

262 months

Tuesday 28th April 2009
quotequote all
Get some pics and let us know how you get on. Part of me would have liked to have done it myself. Money could have gone on another service then instead!

crackedfinger

1,569 posts

260 months

Wednesday 29th April 2009
quotequote all
paulathome said:
Remove gearbox and lower gently to the floor. (don't use head as axle stand like I did)
ha ha!

siwebster

417 posts

224 months

Wednesday 29th April 2009
quotequote all
Just had my clutch replaced including fork, bearings, etc for £600 all in at a well known TVR independent. Shop around a bit and you'll get it for half the price you've been quoted without the hassle of doing it yourself...

schmokin1

1,223 posts

243 months

Wednesday 29th April 2009
quotequote all
paulathome said:
I managed it on the drive took about 12 hours with many brews in the process.
Oh and it rained most of the time furious
Hope this helps and convinces you to pay someone else to do it.
Cheers.
Paul

Edited by paulathome on Tuesday 28th April 18:12
roflroflroflrofl

know exactly what you mean tho!