Upper DIff bush - I've won!
Upper DIff bush - I've won!
Author
Discussion

hibutts

Original Poster:

38 posts

218 months

Wednesday 29th April 2009
quotequote all
After experiencing a clonk when coming off the gas quickly, I had a quick look at the diff. All bolts tight but the upper bush was split to pieces - bugger. Anyway after reading the various topics on here and the Griff forum I bought a Brtitool void bush removal tool (for Ford radius arms and Salisbury axles).

I acquired a new two piece bush from Racing Green and they advised the diff has to come out and then its a process of heating, cutting, banging, swearing and treating the various injuries to get the old one out. Once this is achieved the new one pushes in easily.

Well, against their advice I took the decision to do the job with the diff in-situ. Several times during the job I came close to regretting this.

After I had managed to get the bush bolt undone via the O/S wheel arch , the biggest problem with leaving the diff was removing the diff-to-bush bracket - its really tight up there. Anyway with a bit of gentle persuasion and moving the diff up and down I managed to get it out.

Once out the Void Bush Tool fitted in place neatly and using the "tighten a bit and then bash the end of it" technique (lond drift required) the bush slowly came out. No cutting, heating or even much swearing. I did soak in lots of WD40 over night.

Getting the bracket back in was quite difficult too. Drop diff as low as possible, push bracket up as close into place as you can and then raise diff slowly whist persuading the bracket back into place.

Do all bolts up - job done.

All in all it took about 4 hours.

Not for the faint hearted but do-able on your own if you have lots of extension bars, ratchets, hammers and drifts etc.

Now just noticed one of the rear shocks is leaking badly and I have an MOT in 2 weeks time. Anyone got a serviceable one they don’t want to help me through the MOT before I commit to a brand new set??!!!

Hope this helps someone in the same position.

Nick

sapper

1,134 posts

236 months

Wednesday 29th April 2009
quotequote all
Perfect timing.... guess what im doing tomorrow,
ive just changed the suspension bushes and the diff bush is next. i have a full set of shocks as ive just put new ones on but im nowhere near hampshire.

hibutts

Original Poster:

38 posts

218 months

Wednesday 29th April 2009
quotequote all
Good luck!
If your doing it with the diff in just keep telling yourself "it can be done"!

Seasider

12,728 posts

280 months

Wednesday 29th April 2009
quotequote all
hibutts said:
Good luck!
If your doing it with the diff in just keep telling yourself "it can be done"!
It certainly can biggrin

HRG

72,863 posts

270 months

Wednesday 29th April 2009
quotequote all
4 hours? Took me four fking weeks to do all three... hehe

Seasider

12,728 posts

280 months

Wednesday 29th April 2009
quotequote all
HRG said:
4 hours? Took me four fking weeks to do all three... hehe
It felt like 4 fking years the way you were going on about it wink

tuscan_al

4,112 posts

245 months

Wednesday 29th April 2009
quotequote all
Nice job, I gave up with my tuscan one and called the AA! APM sorted it, just couldnt get the diff bracket out. Even bought the britool thing frown

hibutts

Original Poster:

38 posts

218 months

Thursday 30th April 2009
quotequote all
Perhaps I made it sound a bit easy.

To put it into perspective, its a job i will never do again!


sapper

1,134 posts

236 months

Thursday 30th April 2009
quotequote all
Bugger,,,,,,,i'mabout to start this, car is up in the air,, loads of penetrant spray last night. and i want the car on the road tomorrow.

tuscan_al

4,112 posts

245 months

Thursday 30th April 2009
quotequote all
sapper said:
Bugger,,,,,,,i'mabout to start this, car is up in the air,, loads of penetrant spray last night. and i want the car on the road tomorrow.
GOod luck frown
The bolt out and diff bush out bit looked east, it was just the damm bracket, couldnt wiggle the diff into the right way even with one of the side mounts off, but maybe I quit too early.

Anyway off to pick mine up from APM now with a lovely new diff bush biggrin

hibutts

Original Poster:

38 posts

218 months

Thursday 30th April 2009
quotequote all
I hope yu mamage it. If you have all day you might be fine.
The worst bit is definitly getting the the old bush bold undone and getting then bracket back in and the bolts to line up. The diff on mine had moved about 3mm to the left so i had to use a long bar to push it back whilst trying to get the hex bolts back in. I used a short 8mm bolt with two nuts on it, turned backwarks and put into a small ratchet. Much easier than using an allen key. I couldn't get hold of a proper attachment for a 1/4 or 3/8 ratchet.

Seasider

12,728 posts

280 months

Thursday 30th April 2009
quotequote all
hibutts said:
I hope yu mamage it. If you have all day you might be fine.
The worst bit is definitly getting the the old bush bold undone and getting then bracket back in and the bolts to line up. The diff on mine had moved about 3mm to the left so i had to use a long bar to push it back whilst trying to get the hex bolts back in. I used a short 8mm bolt with two nuts on it, turned backwarks and put into a small ratchet. Much easier than using an allen key. I couldn't get hold of a proper attachment for a 1/4 or 3/8 ratchet.
I've never thought of that smile must be even better with a ratchet spanner biggrin

GJOSDDLO

92 posts

211 months

Thursday 30th April 2009
quotequote all
I get the clunk also!

I might have a go at doing this...

sapper

1,134 posts

236 months

Thursday 30th April 2009
quotequote all
Just had a good look.The bushes look pretty good, but ive bought new so they will be changed. 2 bolts were missing from the plate and 1 is very loose.yikes
Strange how this was up on ramps recently and I was told i needed new bushes all round but the loose and missing bolts were never mentioned.

hibutts

Original Poster:

38 posts

218 months

Thursday 30th April 2009
quotequote all
If they just took a cursory look from underneath the bolts are quite difficult to see if. However if you looking for a reason for the clonking thats got to be one of the first thisgs you check. Lucky the diff didn't end up in the boot!

penno

241 posts

261 months

Thursday 30th April 2009
quotequote all
Took me the best part of a week to remove the bush lining but did it with the diff in situ. Anyone managed to do the front bushes without dropping the diff I tried couldn't budge the bushes so gave up since they looked OK . Where did you get the removing tool from?

hibutts

Original Poster:

38 posts

218 months

Thursday 30th April 2009
quotequote all
I thought you could remove the two front brackets off the diff, supporting it from underneath and remove them from the car.

I bought the tool on eaby, itme number 130302326367 £22 delivered. I don't think its any good withough modification for any other bushes on the car but it worked a treat on the upper bush which is the same size as the two lower ones.

450 Paul

41 posts

223 months

Thursday 30th April 2009
quotequote all
I put some Gaz golds on and still have the originals somewhere in the garage and I dont want much for them if you are interested? Very impressed with sorting the bush out with diff in place!

hibutts

Original Poster:

38 posts

218 months

Thursday 30th April 2009
quotequote all
Thank you very much for the offer, I have the MOT in a couple of weeks so will let you know if i get stuck. Sounds like some Gaz items will be on the list for later in the year!

GJOSDDLO

92 posts

211 months

Thursday 30th April 2009
quotequote all
Anyone have any pics of the process?

I'm hoping to start this on Monday.