Today's Horrors!!!
Discussion
Decided to drop the sump today - it was weeping a little and as I was going to change to the oil anyway (from 0W40 to 15W50 to try to keep the pressure higher when hot - currently 15 at tickover and 30 at revs when 70 degrees plus) so off I went... 
Horror 1 : Read the bible, it said the oil might shoot out a bit, 6 inches or so from the sump plug... Aaaaargh...it actually shot out about 12 inches from the plug, and so fast that my drain canister couldn't copw with the flow... Upshot of this is me cover in oil (arm, face, neck and down the inside of my t-shirt) and also the brick paved drive about 5mm deep in Mobil's finest!!! The missus is NOT impressed...
Horror 2 : Drop the sump and just find myself lost for words... The pick-up has 3 pieces of gasket sealant and a piece of emery paper stuck in the end of it... I could see about a fifth of the mesh and the rest was obscured!!!
Now all back together and I'm waiting for the silicone on the new gasket to harden a bit before I run the engine for any length of time, but I had a full 45 psi coming off the ramps and managed to not need to re-prime the oil pump.
Hope you all had better days than I did - could have averted a future disaster though...
Giles

Horror 1 : Read the bible, it said the oil might shoot out a bit, 6 inches or so from the sump plug... Aaaaargh...it actually shot out about 12 inches from the plug, and so fast that my drain canister couldn't copw with the flow... Upshot of this is me cover in oil (arm, face, neck and down the inside of my t-shirt) and also the brick paved drive about 5mm deep in Mobil's finest!!! The missus is NOT impressed...

Horror 2 : Drop the sump and just find myself lost for words... The pick-up has 3 pieces of gasket sealant and a piece of emery paper stuck in the end of it... I could see about a fifth of the mesh and the rest was obscured!!!

Now all back together and I'm waiting for the silicone on the new gasket to harden a bit before I run the engine for any length of time, but I had a full 45 psi coming off the ramps and managed to not need to re-prime the oil pump.

Hope you all had better days than I did - could have averted a future disaster though...
Giles
Tip - use neoprene gloves or a set of marigolds and control the initial flow of oil with the nut just release oil gradually for a while .. and always spread about plenty of paper under the collection can.
Last tip .. cement powder .. put it on the oil spill and work it in .. it will soak up the oil spill.
They use this method at race tracks ... works well enough and I've had a few.
Last tip .. cement powder .. put it on the oil spill and work it in .. it will soak up the oil spill.
They use this method at race tracks ... works well enough and I've had a few.
It's the sort of thing that's only going to catch you out once, but if you get fed up with oil everywhere you could try a dry break sump plug from difflock:
http://shop.difflock.com/difflock-drainplug-c-4.ht...
(I think they're dry break - I haven't seen one close up.)
http://shop.difflock.com/difflock-drainplug-c-4.ht...
(I think they're dry break - I haven't seen one close up.)
I figured that next time I'd use a large black bucket to catch the oil in rather than trying to be clever with a fancy draining can!
I scrubbed in a whole bottle of washing up liquid and then rinsed it all down, and this morning it just looks like a wet patch in the drive...still in the dog house...
I scrubbed in a whole bottle of washing up liquid and then rinsed it all down, and this morning it just looks like a wet patch in the drive...still in the dog house...

Go to machine mart and get some concentrated parts washer fluid - you dilute it but mix it pretty strong and it should lift the oil. Only a tenner or so for 5 litres.
I guess you maybe able to ge something more specific like driveway cleaner or something.
Worst case go to a builders merchants and get some new matching block paving bricks, or swap them with some that aren't very visible.
I guess you maybe able to ge something more specific like driveway cleaner or something.
Worst case go to a builders merchants and get some new matching block paving bricks, or swap them with some that aren't very visible.
Edited by Barkychoc on Thursday 30th April 09:47
Clippy
I use one of these:
http://www.pelapumps.co.uk/default.aspx?orig=ga
Just get the oil warm first otherwise it takes ages.
HTH
edit; the 6 ltr spherical one is the one that I have.
I use one of these:
http://www.pelapumps.co.uk/default.aspx?orig=ga
Just get the oil warm first otherwise it takes ages.
HTH
edit; the 6 ltr spherical one is the one that I have.
Edited by griffdude on Thursday 30th April 18:09
That looks like a really smart bit of kit, and no scrabbling around underneath except for the oil filter - result!
I think part of the problem was the fact that I'd warmed the oil with a 30 mile blast before hand, thinning it out nicely to reach the parts that other oils just don't reach even when they're warm!
The crud in the pick-up is now worrying me slightly on the basis that it may have been reducing the flow and causing oil starvation in the cam or rocker area...but with the new, thicker oil in there are no ticks, clunks or rattles at all from the engine, so I'll just assume everything's OK.
Engine was rebuilt 2,500 miles ago for the previous owner - I guess the debris is the result of that exercise... I now know who not to recommend for this kind of work in the Ashford area...if you live there and would like to know who did the work I'll happily share, but obviously not via the forum...
Giles
I think part of the problem was the fact that I'd warmed the oil with a 30 mile blast before hand, thinning it out nicely to reach the parts that other oils just don't reach even when they're warm!
The crud in the pick-up is now worrying me slightly on the basis that it may have been reducing the flow and causing oil starvation in the cam or rocker area...but with the new, thicker oil in there are no ticks, clunks or rattles at all from the engine, so I'll just assume everything's OK.
Engine was rebuilt 2,500 miles ago for the previous owner - I guess the debris is the result of that exercise... I now know who not to recommend for this kind of work in the Ashford area...if you live there and would like to know who did the work I'll happily share, but obviously not via the forum...
Giles
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





Keep it off forum please guys !!!

