Anyone have a link to roof removal ??....................
Anyone have a link to roof removal ??....................
Author
Discussion

Mad Mitch

Original Poster:

842 posts

259 months

Thursday 7th May 2009
quotequote all
Just wanting to tighten or remove and re fit rear roof section. Cant find the info through the search facility. Any one have a link ?? Cheers
Steve.

lewis_sharman

5,958 posts

222 months

Thursday 7th May 2009
quotequote all
I believe there is one on the chimaera or griffith pages. Sorry i don't have a link, am shooting off to bed now sleep

philmccann

430 posts

231 months

Thursday 7th May 2009
quotequote all
There is a good write up on the griffith pages written by a guy fitting one of Dave Hammerton's hoods.

I am in the process of replacing mine right now. It would not be easy to remove and refit your hood as, if it anything like mine, it is seriously glued on, both at the back and across the targa.

I had great trouble getting it freed from both these. So, unless it absolutely necessary to remove it, I would not advise unless you intend to replace with new.

HTH

Phil

kenny Chim 4

1,604 posts

289 months

Thursday 7th May 2009
quotequote all
philmccann said:
There is a good write up on the griffith pages written by a guy fitting one of Dave Hammerton's hoods.Phil
Here: http://www.thegriffithpages.com/modifications/exte...
philmccann said:
I am in the process of replacing mine right now. It would not be easy to remove and refit your hood as, if it anything like mine, it is seriously glued on, both at the back and across the targa.
Phil
I found that the main problem was engaging and removing the two hidden bolts, forward (each side) of the three retaining nuts (accessed via the boot) that secure the lower hood hard-hoop in place.

You will not be able to access their retaining nuts and I ended up using a hacksaw to remove their bolt heads.

Dave concurred that he had the same problem when changing his Griff's roof.

As an aside, Dave's kit really is a fantastic replacement as the material is sandwiched by a rubber membrane which negates ever having to waterproof the material again.

Dave is also very helpful with regards to fitment.

philmccann

430 posts

231 months

Friday 8th May 2009
quotequote all
Unfortunately, mine is not one of Dave's hoods. He had no blue ones in stock nor any intention of doing so in the near future. Got mine from BAS. Looks pretty good. Have the old one off now, and as I said it was VERY well glued down. I had to use a wire brush on the dril to remove the glue. Evo-Stik remover would not touch it.
Also repaired the front edge of the targa as some bits had broken away.
It is P*****g down here for the last few days so haven't got it out to do it. Must say I am a bit wary of it. Tried the double sisded tape idea, but don't know if the tape I have is crap but not powerful enough to stick the hood to. So, going to have to use measuring techniques to line it all up.

Which is best to glue down first, targa or tension ring?? and how do you know how much tension it should all have on when closed??

Rgds

Phil

hibutts

38 posts

218 months

Friday 8th May 2009
quotequote all
Probably a bit late but for future reference, if you need to remove the old glue try using "Sticky Stuff Remover" spray. Its about £5 on ebay. Spray on, leave for 10-15 minuts and srape off the old glue. Repeat where the glue is thick. I then used used an old rag with the spray to clean up the last few bits. Worked a treat.

kenny Chim 4

1,604 posts

289 months

Saturday 9th May 2009
quotequote all
philmccann said:
Which is best to glue down first, targa or tension ring?? and how do you know how much tension it should all have on when closed??
Phil
Carefully attach and glue (using Impact) the lower tension assembly first ensuring it stretches evenly across the back from behind each glass window.

After at least 10 minutes, raise the Targa hoop (without locking) and test the fitment of the side material and rear window by pulling it forward over the front edge of the Targa hoop.

If this all appears to fit, then use a can of Loctite Spray Adhesive and apply to both the mohair and the top of the hoop (this glue adheres to itself). Quickly lock the Targa struts in place and check you have a wave free rear window- especially vertically. If not, strip the fabric from the hoop and re-adjust until the back window is smooth.

philmccann

430 posts

231 months

Sunday 10th May 2009
quotequote all
Thx for all that

From the write up in the griffith pages they use double sided tape first to line it all up. I tried some B&Q cr*p and it wouldn't stick anything. Any ideas which double sided tape is the one. S**t scared of getting into a mess after applying the glue.

Rgds

Phil

kenny Chim 4

1,604 posts

289 months

Tuesday 12th May 2009
quotequote all
Phil, sorry for the belated reply.
Yep, even the double-sided tape that Dave supplies with his kit is far too weak considering the tension involved. You really have no choice but to make a judgement and go for it.

The adhesives involved do allow for adjustment though.. more than once, and you can strip your last attempt back and re-apply without losing the quality of the new hood.

Something I failed to mention is that the top edge of the fabric has to be glued with Impact or similar, (once you are happy with the fit), along the leading edge of the front hoop. There is a recess there which accomadates the rear edge of the targa panel and its tension has to be correct. Once happy, simply lock the rear struts after the upper (and lower hoop) is securely set.

philmccann

430 posts

231 months

Tuesday 12th May 2009
quotequote all
Cheers Kenny

Have got the rear hoop done now and really happy with that. Unfortunately away to work for a couple of weeks.So, will complete on my return. If it turns out as good as the rear I will be more than pleased.

Thx for all the help

Phil