Chimaera Brake Failure
Chimaera Brake Failure
Author
Discussion

PxMetro

Original Poster:

43 posts

220 months

Sunday 10th May 2009
quotequote all
As I was approaching home this morning after a fantastic drive out, I became aware that the brake pedal travel was becoming increasingly excessive, to the point where the pedal now travels all the way down to what feels like a mechanical stop, with virtually no braking effect now at all. (Scary)
I have thoroughly bled the brakes through, and did get some air out at the front, but still have no brakes.
The symptoms sort of suggest that the Master Cylinder seals are shot. There are no visible signs of fluid leaks anywhere (inside or under the car) Has any body experienced these symptoms, and if so what was the remedy?

Looking at the Steve Heath "Bible" the Master Cylinder is a pig to get out.

Cheers

scotty_d

6,795 posts

225 months

Sunday 10th May 2009
quotequote all
Hi it does sound like the Master Cylinder seals are passing. and if there are no fluid leaks from anywhere else i would look at it.

PxMetro

Original Poster:

43 posts

220 months

Sunday 10th May 2009
quotequote all
Thanks Scotty. I think you're right, it needs looking at, but unfortunately no quick miracle cure.

Cheers

lotusandy

257 posts

302 months

Sunday 10th May 2009
quotequote all
If you can, clamp all 4 flexi hoses, then if you still have loads of pedal travel it must be the master cylinder, if you can just clamp 1 at a time it might be worth doing each in turn to see if there is a specific claiper that is causing the trouble.

Andy

roysum

961 posts

220 months

Sunday 10th May 2009
quotequote all
There is a bleed nipple on the master cylinder, accessible through the clutch reservoir cover. Not the easiest thing to get a tube and spanner on though.

Roy

PxMetro

Original Poster:

43 posts

220 months

Sunday 10th May 2009
quotequote all
Thanks all for your input and ideas. All being well I shall start to pull it apart next week end


byebyesmash

AirconAde

104 posts

226 months

Sunday 10th May 2009
quotequote all
Hi there.

I have just changed my brake master cylinder as it was leaking from the main seal.

I managed to do it without removing the pedal box the only thing I had to do was remove the reservoir and the clutch master cylinder cover so that I could get a spanner onto the pipes. It was a bit of a fiddle but was done in under an hour including bleeding the brakes.

Ade

sparkythecat

8,114 posts

286 months

Sunday 10th May 2009
quotequote all
^^^

AirconAde pictured earlier today


myquest

78 posts

258 months

Sunday 10th May 2009
quotequote all
I had something similar caused by a seized caliper which boiled the brake fluid and gave me a long pedal, Check the wheels are spinning freely and, was your engine temp much higher in slow traffic? Worth checking

schmokin1

1,223 posts

243 months

Monday 11th May 2009
quotequote all
AirconAde said:
Hi there.

I have just changed my brake master cylinder as it was leaking from the main seal.

I managed to do it without removing the pedal box the only thing I had to do was remove the reservoir and the clutch master cylinder cover so that I could get a spanner onto the pipes. It was a bit of a fiddle but was done in under an hour including bleeding the brakes.

Ade
i look forward to seeing you as the 'marvelous elastic magician man' on Britain's got talent! Do let us all know when you are onbiggrinbiggrinbiggrinbiggrinbiggrinbiggrin

PxMetro

Original Poster:

43 posts

220 months

Monday 11th May 2009
quotequote all
schmokin1 said:
AirconAde said:
Hi there.

I have just changed my brake master cylinder as it was leaking from the main seal.

I managed to do it without removing the pedal box the only thing I had to do was remove the reservoir and the clutch master cylinder cover so that I could get a spanner onto the pipes. It was a bit of a fiddle but was done in under an hour including bleeding the brakes.

Ade
i look forward to seeing you as the 'marvelous elastic magician man' on Britain's got talent! Do let us all know when you are onbiggrinbiggrinbiggrinbiggrinbiggrinbiggrin
Not doubting your word at all, but I think you would have to be an elastic man to get in through the clutch master cylinder aperture. I remember changing the clutch master cylinder a couple of years ago, and hoping I would never have to remove that cover ever again.
laugh

roysum

961 posts

220 months

Monday 11th May 2009
quotequote all
Blimey ! I'm impressed