Block Questions
Discussion
Hi all,
I'm sold on the idea of getting a SC Power Supercharger for my 400 serp but I'd want the engine to be in tip top condition before I bolt one of those bad boys on!
The motor had a part rebuild after a slipped liner a year or so ago but was only replaced with a standard liner. (If I'd known about Top Hats at the time I'd have had them done!)
Anyway, aside from Top Hats, what else should I be doing this time around to ensure a healthy prosperous engine that will take all the extra fuel/air with no problems down the line.
Someone mentioned the 'quality' of the blocks can sometimes be questionable and to look for some sort of colour mark to indicate the thickness of certain walls. Should I get the block pressure tested before Hatting it?
What about cross-bolting? I've heard this is desirable. Will mine already be cross-bolted - can I easily check?
Cheers,
Ryan
if i had the choice i would go for a new engine .ive just looked on the v8 d website and i would go for this instead of a supercharger kit .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
That is a very attractive option actually Daz, Hadn't really considered that. My only worry is 'Is it going to be a f
ker to drive round town at normal speeds'.I've heard tales of wild cams/highly tuned setups being too snatchy and difficult at more pedestrian speeds - I love the smoothness of my 400 round town but want it to fly when I get past 3500!
daz the plumber said:
if i had the choice i would go for a new engine .ive just looked on the v8 d website and i would go for this instead of a supercharger kit .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
But then again a nice new 4.6 with a blower would be even more interesting!v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
If you go for a blower I don't think you need to go berserk with the porting - obviously it will help but I don't think the gains are so great as the induction is under pressure anyway.
If you go for a blower you need a tame cam not a wild one - you could always go for a 4.6 built with a blower in mind with appropriate blower cam then add the blower when your wallet allows!
Edited by Barkychoc on Tuesday 12th May 09:27
think the above set up would satisfy most peeoples needs , the stelth cam is still smooth just one up from the mc1 cam . if i had my chance again , i would of ditched my engine and start a fresh .this set up is far quicker than the chim 5l .wonder what the lot costs .
http://www.v8developments.co.uk/
http://www.v8developments.co.uk/
Edited by daz the plumber on Tuesday 12th May 21:19
I found deciding which route to take in quest of a nice driveable engine with an adequate amount of power rather more complex than it first appeared. Simply bolting on a blower kit looks a good choice and it seems quite a few are happy with the result, but. Ideally for the blower you need a nice mild cam without a lot of overlap and a not too high compression ratio. A lot of cars have already had the exact opposite done mine included, so to make a proper job of it you may need to at least fit a milder cam. Then there is the bottom end. Advice from the “engine builders” is to only start looking for significant power increases if the bottom end is cross bolted, some are and some are not. This is particularly important with the 500. Then you have to worry about the pistons, are they appropriate for forced induction. Whilst thinking about the bottom end it is worth considering a properly balanced crank rather than the TVR arrangement. You can end up specifying effectively a complete new engine build before thinking about the blower. While doing that you may as well, depending on how much power you and your transmission want end up simply specifying a reasonably high spec NA engine. Just to complicate the situation more many of the questions seem get a different answer depending on which “expert” you ask. Is a new block or a “seasoned” one better for example
A not insignificant point is insurance, The insurance companies seem terrified as soon as you mention super let alone charger, they do however appear less concerned about modified NA
A not insignificant point is insurance, The insurance companies seem terrified as soon as you mention super let alone charger, they do however appear less concerned about modified NA
daz the plumber said:
if i had the choice i would go for a new engine .ive just looked on the v8 d website and i would go for this instead of a supercharger kit .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
This is what i have had done i decided not to go the supercharger route the 4.6 with the above mods is a big increase in power over my old 4.0 and is cross bolted with top hats, i dont know what figures it is putting out yet but it pulls like a train with no shunting at low speeds i would only consider the sc option if your engine is in tip top condition and is cross bolted, coming from 4 litre chimaera the 4.6 gave me a big increase in power with the knowledge that my engine is in excellent condition.v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
yep i too wanted a beefy bottom end before the SC route, more so on the 500 as it has been mentioned that cranks can be a weak point, i wanted torque and car that is happy driving through town to a hoon. I have opted for a camshaft from power that suits the SC kit, in addition have gone for steel crank, H beam rods, forged pistons and a top hatted 5.4 block, heads are V8 Dev with lower compression and O ringed with yella terra rockers. this should handle whatever the SC throws at it. the power can be limited by the pulley arrangement on the blower.
Edited by hiltonig on Thursday 14th May 08:13
robbri said:
daz the plumber said:
if i had the choice i would go for a new engine .ive just looked on the v8 d website and i would go for this instead of a supercharger kit .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
This is what i have had done i decided not to go the supercharger route the 4.6 with the above mods is a big increase in power over my old 4.0 and is cross bolted with top hats, i dont know what figures it is putting out yet but it pulls like a train with no shunting at low speeds i would only consider the sc option if your engine is in tip top condition and is cross bolted, coming from 4 litre chimaera the 4.6 gave me a big increase in power with the knowledge that my engine is in excellent condition.v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .

daz the plumber said:
think the above set up would satisfy most peeoples needs , the stelth cam is still smooth just one up from the mc1 cam . if i had my chance again , i would of ditched my engine and start a fresh .this set up is far quicker than the chim 5l .wonder what the lot costs .
http://www.v8developments.co.uk/
Agree that the cam is smooth at tick over, but it is a stonking cam! Cant see why the modded 4.6 route would be far quicker than a std 500 in good order? http://www.v8developments.co.uk/
Edited by daz the plumber on Tuesday 12th May 21:19
Chimjunkie said:
Agree that the cam is smooth at tick over, but it is a stonking cam! Cant see why the modded 4.6 route would be far quicker than a std 500 in good order?
My 4.6 out paced a good friend's 5.0lt along the main straight at Bruntingthorpe a few years ago (before fitting the Emerald & V8enhancements manifolds).Chimjunkie said:
robbri said:
daz the plumber said:
if i had the choice i would go for a new engine .ive just looked on the v8 d website and i would go for this instead of a supercharger kit .
v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .
This is what i have had done i decided not to go the supercharger route the 4.6 with the above mods is a big increase in power over my old 4.0 and is cross bolted with top hats, i dont know what figures it is putting out yet but it pulls like a train with no shunting at low speeds i would only consider the sc option if your engine is in tip top condition and is cross bolted, coming from 4 litre chimaera the 4.6 gave me a big increase in power with the knowledge that my engine is in excellent condition.v8d stealth camshaft
4.6 long engine (stage 3 heads)
72mm ported plenum chamber
45mm ported inlet manifold
45mm ported trumpet base .
that would be my choice . a nice new engine .

If I'm building a turbo bottom end it usually gets a stud kit for the mains, ARP bolts for the rods and a set of really good shells. Also on the agenda and of major importance is making sure the rings are suitable and the pistons are nice and strong preferably forged with the right bowl volume to suit the compression required. Pistons subjected to boost experience higher average cylinder pressures and a higher peak pressure which is only for a nano moment. This is also when detonation can massively increase pressure, at the point of peak torque. However, if the ring lands aren't designed to be stronger then detonation can crack them and then you're stuffed. Detonation is far more likely and damaging with a forced induction engine.
Early rovers have terrible pistons with slotted skirts, next to useless for forced induction. Cross bolted engines have much better pistons and rods, these don't need changing in less you have plans for high boost and want to lower compression and make a few improvements. I've never seen a problem with a stock crank on any of the stock rovers using any form of boost. Early rods aren't much cop but seem ok with a bolt upgrade while using sensible rpm's.
Top ends can remain stock if the budget won't stretch to anything fancy. After all, the increase in air is being done by forced induction.
Early rovers have terrible pistons with slotted skirts, next to useless for forced induction. Cross bolted engines have much better pistons and rods, these don't need changing in less you have plans for high boost and want to lower compression and make a few improvements. I've never seen a problem with a stock crank on any of the stock rovers using any form of boost. Early rods aren't much cop but seem ok with a bolt upgrade while using sensible rpm's.
Top ends can remain stock if the budget won't stretch to anything fancy. After all, the increase in air is being done by forced induction.
robbri said:
Boosted how are your turbo conversions coming along, what is involved as i may consider this option in the future any idea on price including remaping?
+1 
Cant go down the SC route as my 4 litre engine is a pre serp. Would absolutely love a low pressure turbo to give a bit more power.
I'm been held up machining the bolt in Y piece turbo manifold. It's been very frustrating waiting for this to be finished. Hopefully it will be done next week and then I can fit it onto a car. Spend has something that resembles a car so I'll try that
Then I can choose an after market cat to fit in front of the engine and link into the existing exhaust system and that's the hardware side of things finished.
I intend to ofer a fitting service only. For mapping the car could go to Joo who is near me and he knows what to do. The sump will need to be modded for a turbo oil drainback but I'd do that as a part of the installation.

Then I can choose an after market cat to fit in front of the engine and link into the existing exhaust system and that's the hardware side of things finished.
I intend to ofer a fitting service only. For mapping the car could go to Joo who is near me and he knows what to do. The sump will need to be modded for a turbo oil drainback but I'd do that as a part of the installation.
daz the plumber said:
think the above set up would satisfy most peeoples needs , the stelth cam is still smooth just one up from the mc1 cam . if i had my chance again , i would of ditched my engine and start a fresh .this set up is far quicker than the chim 5l .wonder what the lot costs .
http://www.v8developments.co.uk/
That's nearly the same spec as my 4.6 originally, but I think it's a bit optimistic to expect it to be more powerful than a TVR 500. Power is close, torque is some way down.http://www.v8developments.co.uk/
However, a cross bolted 4.6 with good induction is superb value for money (compared to some of the more highly tuned alternatives) and makes an excellent base engine for supercharging.

Gassing Station | Chimaera | Top of Page | What's New | My Stuff


