help b*@@*y ball joints
Discussion
Got new top and bottom ball joints, track rod ends and engine mounts. Did the engine mounts this pm, passenger side a swine driver's a doddle. Thought I'd just do the trackrod ends before finishing, couldn't break the lock nut on either side despite swamping in WD40, eventually got nearside to release and fitted new end allowing for slight differnce in length.
The offside one won't budge and I think I may have rounded it, any suggestions as to anything else I can do ? Or do I have to admit defeat and get the guys doing the geo to do it?
I'm also a bit puzzled as to how I can split the top ball joint from the hub carrier due to the end of the joint being recessed in the carrier.
Any suggestions gratefully received as I am hoping to get all this done by the weekend.
Thanks
The offside one won't budge and I think I may have rounded it, any suggestions as to anything else I can do ? Or do I have to admit defeat and get the guys doing the geo to do it?
I'm also a bit puzzled as to how I can split the top ball joint from the hub carrier due to the end of the joint being recessed in the carrier.
Any suggestions gratefully received as I am hoping to get all this done by the weekend.
Thanks
Whist you at machine mart this may help with the seized nut:
http://www.machinemart.co.uk/shop/product/details/...
http://www.machinemart.co.uk/shop/product/details/...
When I did mine, I had a 'mare splitting the joint from the upright. It's the only job on any vehicle where I had to go out and buy a bigger hammer (and it still didn't come apart with big FO joint splitter) 
In the end, it did came apart with just one very sharp tap from a ball pein hammer and no splitter wedge....on the side of the 'cone' part of the upright. Apparently, done right, this is enough to distort the internal taper so that the bond with the joint is broken.... Was a tip from an indie and worked a treat

In the end, it did came apart with just one very sharp tap from a ball pein hammer and no splitter wedge....on the side of the 'cone' part of the upright. Apparently, done right, this is enough to distort the internal taper so that the bond with the joint is broken.... Was a tip from an indie and worked a treat

Had mine off last week to fit a new gaiter to the steering rack. Had one similar to this in the garage, worked a treat!!!
HTH
Phil
http://www.shop-com.co.uk/Sealey_Ball_Joint_Puller...
HTH
Phil
http://www.shop-com.co.uk/Sealey_Ball_Joint_Puller...
For the track rod end if you can't get it to shift saw the balljoint and socket off the end (so the shaft of the balljoint is still there but you can get the tool below over the remaining bit) then use one of these to split the nut.
http://www.machinemart.co.uk/shop/product/details/...
http://www.machinemart.co.uk/shop/product/details/...
I'm also a bit puzzled as to how I can split the top ball joint from the hub carrier due to the end of the joint being recessed in the carrier.
You can remove the top ball joint adapter by dressing the weld off the lower part of the locating tag (as these are welded on after the adapter is fitted) undoing the locking bolt out of the ford casting, and then work with this off the car (if someone PMs me direct and wants to host a couple of pictures of the parts as new adrian@exactly.demon.co.uk
Adrian@
You can remove the top ball joint adapter by dressing the weld off the lower part of the locating tag (as these are welded on after the adapter is fitted) undoing the locking bolt out of the ford casting, and then work with this off the car (if someone PMs me direct and wants to host a couple of pictures of the parts as new adrian@exactly.demon.co.uk
Adrian@
Barkychoc said:
For the track rod end if you can't get it to shift saw the balljoint and socket off the end (so the shaft of the balljoint is still there but you can get the tool below over the remaining bit) then use one of these to split the nut.
http://www.machinemart.co.uk/shop/product/details/...
Hmmm.. quick bit of heat and some agricultural stilsons would be a lot easier IMHO.http://www.machinemart.co.uk/shop/product/details/...
Thanks Dave......These are the 2 parts that make up the top ball joint adaptor, the male part gets dropped into the Ford upright and the locking tang then get welded into place...to remove it, remove the clamp bolt, dress off the the lower weld on the tang and knock out of the upright (this allow stubborn ball joints to be drilled out from the inside)
Adrian@

The tang can be welded back on (if you have dressed that much off that it requires it) when it is off the car, as long as the new weld can pass down the slot on the upright.
Adrian@
The tang can be welded back on (if you have dressed that much off that it requires it) when it is off the car, as long as the new weld can pass down the slot on the upright.
Edited by Adrian@ on Thursday 14th May 15:27
Thanks for all the assistance guys, finally managed to undo the stubborn track rod and chaged that, then did the offside ball joints. Top came away third sharp hit with hammer and did doth in < 1 hour.
Nearside totally different took 2 1/2 hours as top would not split, then remembered my Vauxhall training and used 2 hammers, 1 held against cone opposite side to the one i hit it with and after 10 or so sharp taps it came appart!
Anyway all done now and booked in for a full geo set up next week, also took the opportunity to clean up the front corners of the chassis and outriggers. Will let dry overnight then put wheels back on and check out the difference in the suspension.
Thanks again for the help.
mike
Nearside totally different took 2 1/2 hours as top would not split, then remembered my Vauxhall training and used 2 hammers, 1 held against cone opposite side to the one i hit it with and after 10 or so sharp taps it came appart!
Anyway all done now and booked in for a full geo set up next week, also took the opportunity to clean up the front corners of the chassis and outriggers. Will let dry overnight then put wheels back on and check out the difference in the suspension.
Thanks again for the help.
mike
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




