Newbie Chim questions
Discussion
Have been looking at Chimaeras, on and off, for a little while now, as I think they offer great value for money in terms of performance, noise and open-top motoring. Currently, I've got a slightly modified C6 Corvette as a daily driver and an AC Cobra replica with 450bhp as a weekend toy. I'm thinking of, either, adding a Chim or selling both the Vette and the Cob and keeping a Chim as a weekend car and getting a 'normal' car for daily use. That approach would also free-up quite a few thousand quid. Anyway, onto the questions...
I test-drove a very nice example of a Chim 450 today. The car was immaculate and the chassis outriggers looked virtually new... all very clean underneath. Questions are as follows:
1. Looking under the bonnet at the serpentine belt path, I could see what looked like a belt tensioner on the offside, but there also appeared to be a PAS pump on the nearside. However, there was no PAS fitted and no AC either. What was I looking at?
2. The underside of the lift-out centre roof panel was carbon fibre. Is this standard?
3. The accelerator pedal was very stiff/heavy. Is this normal, or did it just need lubing-up?
4. The car didn't feel especially quick. Ok, I'm used to 400bhp+ on a daily basis and the Vette is appreciably quicker and more savage (let alone the Cob, which will leave you with a bloody nose and bleeding ears!). Is there MUCH difference between a Chim 450 and a Chim 500? On paper, the 500 is pretty-much on a par with my C6 Corvette, but we all know that Chim 500s are generally about 60-70bhp down on what TVR quoted for them.
5. Typically, how long do clutches and cams last? I know this is difficult to answer as it depends largely on driving style/abuse (at least in terms of clutch life). Are the cams a weak point? All flat-tappet cams with aggressive profiles make me nervous as they all usually have fairly short life-spans and the labour involved is significant on pushrod engines (don't ask me how I know this).
Cheers,
Ian.
I test-drove a very nice example of a Chim 450 today. The car was immaculate and the chassis outriggers looked virtually new... all very clean underneath. Questions are as follows:
1. Looking under the bonnet at the serpentine belt path, I could see what looked like a belt tensioner on the offside, but there also appeared to be a PAS pump on the nearside. However, there was no PAS fitted and no AC either. What was I looking at?
2. The underside of the lift-out centre roof panel was carbon fibre. Is this standard?
3. The accelerator pedal was very stiff/heavy. Is this normal, or did it just need lubing-up?
4. The car didn't feel especially quick. Ok, I'm used to 400bhp+ on a daily basis and the Vette is appreciably quicker and more savage (let alone the Cob, which will leave you with a bloody nose and bleeding ears!). Is there MUCH difference between a Chim 450 and a Chim 500? On paper, the 500 is pretty-much on a par with my C6 Corvette, but we all know that Chim 500s are generally about 60-70bhp down on what TVR quoted for them.
5. Typically, how long do clutches and cams last? I know this is difficult to answer as it depends largely on driving style/abuse (at least in terms of clutch life). Are the cams a weak point? All flat-tappet cams with aggressive profiles make me nervous as they all usually have fairly short life-spans and the labour involved is significant on pushrod engines (don't ask me how I know this).
Cheers,
Ian.
Edited by ian_uk1975 on Friday 15th May 00:32
Sorry that i can only answer a few of your questions, i'm sure someone will answer in more detail in the morning.
-Yes the carbon fibre roof panel is standard
-The accelerator on mine is quite light, i'm guessing the one you drove needed lubing up
-Best bet is to test drive a few to get a good idea on performance. Ive been in quite a few now and they all feel completely different.
-Not sure on clutches, but cams are generally said to lasst 50,000 to 60,000 miles, but there are some people that see over 100,000 without problems.
-Yes the carbon fibre roof panel is standard
-The accelerator on mine is quite light, i'm guessing the one you drove needed lubing up
-Best bet is to test drive a few to get a good idea on performance. Ive been in quite a few now and they all feel completely different.
-Not sure on clutches, but cams are generally said to lasst 50,000 to 60,000 miles, but there are some people that see over 100,000 without problems.
you were probably looking at the idler pully not sure if thats the correct name mine has it to replace the ac pump as i dont have ac or pas,the underside of the roof is only a carbon skin for decoration the roof section made from grp and it is standard.
the loud pedal shouldn't be too stiff but it does have quite a long travel if it felt notchy it may need changing or lubing,
coming from the marques your used too you will need to find a good example of a 4.5 / 5.0ltr to get that kick up the arse your used to but your looking at around 240 to 280 very aproximate figures
cams if looked after can go on for quite a while generally changed about 85k but have been known to go on for a lot longer clutches like you say can vary dependant on use mines been in for about 40k still going strong
im no expert so i'd expect someone to come along shortly to correct me
Rich
the loud pedal shouldn't be too stiff but it does have quite a long travel if it felt notchy it may need changing or lubing,
coming from the marques your used too you will need to find a good example of a 4.5 / 5.0ltr to get that kick up the arse your used to but your looking at around 240 to 280 very aproximate figures
cams if looked after can go on for quite a while generally changed about 85k but have been known to go on for a lot longer clutches like you say can vary dependant on use mines been in for about 40k still going strong
im no expert so i'd expect someone to come along shortly to correct me
Rich
ian_uk1975 said:
2. The underside of the lift-out centre roof panel was carbon fibre. Is this standard?
It's actually carbon look not carbon fibre. The roof is made of GRP which you'll tell when you pick it up.ian_uk1975 said:
3. The accelerator pedal was very stiff/heavy. Is this normal, or did it just need lubing-up?
Shouldn't be too heavy. Most likely just needs a bit of lube. The throttle is cable operated so check the cable is OK as it's a common thing to snap.ian_uk1975 said:
4. The car didn't feel especially quick. Ok, I'm used to 400bhp+ on a daily basis and the Vette is appreciably quicker and more savage (let alone the Cob, which will leave you with a bloody nose and bleeding ears!). Is there MUCH difference between a Chim 450 and a Chim 500? On paper, the 500 is pretty-much on a par with my C6 Corvette, but we all know that Chim 500s are generally about 60-70bhp down on what TVR quoted for them.
The 450 is quick but TBH coming from a Cobra and a Vette it will feel slow. There is a noticeable difference between a 450 & a 500. ian_uk1975 said:
5. Typically, how long do clutches and cams last? I know this is difficult to answer as it depends largely on driving style/abuse (at least in terms of clutch life). Are the cams a weak point? All flat-tappet cams with aggressive profiles make me nervous as they all usually have fairly short life-spans and the labour involved is significant on pushrod engines (don't ask me how I know this).
Cheers,
Ian.
Clutches can be anything from from 20k to over 100k, mine lasted until 40k but thats only because I snapped a clutch fork, the actual plate was fine. Cams again are around 60-80k but many people have done far higher mileage on unworn originals. Depends how you warm the car up and how regularly you service it. I sold mine at 62k and the cams were still in great condition as a rolling road session proved.Cheers,
Ian.
ian_uk1975 said:
3. The accelerator pedal was very stiff/heavy. Is this normal, or did it just need lubing-up?
5. Typically, how long do clutches and cams last?
A bit of lube on the throttle would help. Chims have 2 big return springs its a common mod to remove one of them to improve pedal feel. If its very stiff the cable may be on the way out, check it at the pedal end IIRC thats the most likley point of failure.5. Typically, how long do clutches and cams last?
My 450 clutch was changed at 46k, I reckon I could have made it last to 50k. This is apparently the normal expected life for spirited driving (but no track days).
Cams - I think this totally depends on servicing, driving style and oh lots of other factors. Stories of people having to replace cams at 40k (rare) but plenty of others that go to 100k + on original cams.
Zippee said:
ian_uk1975 said:
2. The underside of the lift-out centre roof panel was carbon fibre. Is this standard?
It's actually carbon look not carbon fibre. The roof is made of GRP which you'll tell when you pick it up. ian_uk1975 said:
3. The accelerator pedal was very stiff/heavy. Is this normal, or did it just need lubing-up?
There are two sets of springs on the throttle mechanism of the plenum. Try taking one spring off to lighten the pedal feel. ian_uk1975 said:
3. The accelerator pedal was very stiff/heavy.
5. Typically, how long do clutches and cams last?
If you're accustomed to "modern" cars, then the TVR accelerator pedal does feel very heavy, but it shouldn't feel stiff. Personally I quite like the weight of the double springs.5. Typically, how long do clutches and cams last?
Unfortunately my cam lasted about 28K - probably an artifact of shorter journeys. My clutch *may* be on its way out at 55K but I've not had that verified.
Thanks for the info chaps.
Can a few more people, who have owned or driven both the 450 and the 500, comment on the performance difference between the two? I do intend test-driving a 500, but a heads-up of what to expect would be good. I also test-drove (few years ago) a 4.2 Cerb. Is the Chim 500 close to the Cerb in a straight-line, or would a Cerb walk all over it?
Can a few more people, who have owned or driven both the 450 and the 500, comment on the performance difference between the two? I do intend test-driving a 500, but a heads-up of what to expect would be good. I also test-drove (few years ago) a 4.2 Cerb. Is the Chim 500 close to the Cerb in a straight-line, or would a Cerb walk all over it?
Edited by ian_uk1975 on Friday 15th May 11:42
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


