Camber settings
Discussion
My rear tyres sometimes catch the rear arches when driving over some of our less than perfect road surfaces.
I have 17'' wheels all round and the rear tyre size is 225/45/17.
Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.
Do i need to get the camber settings changed?
If so has anyone got any experience and reccomendations?
I have 17'' wheels all round and the rear tyre size is 225/45/17.
Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.
Do i need to get the camber settings changed?
If so has anyone got any experience and reccomendations?
mlow said:
I use 2 degrees negative on the rear but do a good number of track days where the extra camber is useful. Half a degree less would probably be sufficient for predominantly road use to avoid wearing the inner edge of the tyres.
If I was to go 1.5 negative on the rear would the front also be adjusted. I asked what the wheel offset was because plainly if you are running 17inch wheels they are not the originals. 225s at the rear are not that wide so I would think if all else is well the camber would have to be a long way off to cause rubbing on the wheel arch. The marking is usually stamped on the rim somewhere, often you will need to take the wheel off to see it. Not looked at the rolling diameter of 225/45/17 but assume you have checked it is similar to the original size. Have you used these wheels /tyres for some time without problems or are they new ?
Stand to be corrected on this one, but here goes.........
I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.). This may also be your problem if you are on non-standard rims and tyres.
Anyone want to confirm or shoot me down?
As my rears are getting worn (can't imagine how
) I might change them before Le-Mans as that is when I usually experience the problem (two up with a boot full of roof and beer!)
J
I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.). This may also be your problem if you are on non-standard rims and tyres.
Anyone want to confirm or shoot me down?
As my rears are getting worn (can't imagine how
) I might change them before Le-Mans as that is when I usually experience the problem (two up with a boot full of roof and beer!)J
sapper said:
My rear tyres sometimes catch the rear arches when driving over some of our less than perfect road surfaces.
I have 17'' wheels all round and the rear tyre size is 225/45/17.
Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.
Do i need to get the camber settings changed?
If so has anyone got any experience and reccomendations?
Yup, I run 1 degree front and rear camber with 265/35 18 on the back and mine foul too. I'm having my inner arches re-glassed this week I have 17'' wheels all round and the rear tyre size is 225/45/17.
Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.
Do i need to get the camber settings changed?
If so has anyone got any experience and reccomendations?
You sure you're only running 225 on the rear?mlow said:
I use 2 degrees negative on the rear but do a good number of track days where the extra camber is useful. Half a degree less would probably be sufficient for predominantly road use to avoid wearing the inner edge of the tyres.
I think that 1.5 degrees neg camber is more than enough but I tend to run more rear toe to aid traction. Konrod said:
Stand to be corrected on this one, but here goes.........
I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.).
Quite true. Tyre brands are very different with their profiles and actual widths.I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.).
Some of the tyres i've had on the rear:
225 bridgestone S03 had 9.25" width
245 Toyo T1R had 9" width
245 Toyo R888 have 10" width!!
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


