Oil Grade/Brand?
Discussion
I am soon getting my Chimaera 400 (1999) with 37k on the clock service and am receiving confliction reports on the grade/brand of oil to use.
The car has had Mobil 1 5W40 (as recommended by TVR Henley) for the past two years, but am wondering if this is still the preferred option?
Thanks in advance
Matt
The car has had Mobil 1 5W40 (as recommended by TVR Henley) for the past two years, but am wondering if this is still the preferred option?
Thanks in advance

Matt
Edited by V6Alfisti on Tuesday 19th May 19:30
to be honest any good oil 10w or 15w 40 or 50 changed at correct intervals should be good i change mine every 3000 miles and my engine is still going strong as i only pay £20 for 5ltrs i can change more frequently for the same money as silkolene, just bought mobile part synthetic 10w 40 £19 for 5 ltrs
SP6 Animal said:
Magnatec
That stuff is just fine,i have used 5/40 fully syn since ownership(my oil consumption is little)and have no problems(bulk buyer)i do however have 2 packs of 15/50 Mobil 1 Motorsport thats going in after the engine mods,why? because i have the stuff already but would be quite happy with a 10/40 5/40 10/50 whatever just avoid the piss like 0/40 5/30 if nothing else i would imagine the oil consumption would rise drastically,but would also go with what Opie Oils recommend 
Edited by Simon Says on Tuesday 19th May 22:02
So even a 10w40 Magnetec would sit very happily in the engine 
I thought I read somewhere that these units are happier with a XXw50 combo?
Also I am planning to do a big trip through France/Italy/Switzerland/Germany at the end of July, do I need to take account of any temp changes?
PS: As I might be getting my local mechanic to do the oil change this time, is there any specific brand of oil filter that is preferred?
Thanks

I thought I read somewhere that these units are happier with a XXw50 combo?
Also I am planning to do a big trip through France/Italy/Switzerland/Germany at the end of July, do I need to take account of any temp changes?
PS: As I might be getting my local mechanic to do the oil change this time, is there any specific brand of oil filter that is preferred?
Thanks

daz the plumber said:
morris oil 10/50fully synthetic thats the best stuff up to yet .
I see your 10/50 and raise you, millers 10/60http://www.millersoils.net/1_Millers_frame_MOTORSP...
Was in my local auto part shop and they had it on the shelf, normally I don't have a problem with what oil to use, just work on the guide lines of not lower than 10 and be made by a firm that has made oil for a good few years, castrol etc, not even bothered about semi or fully synthetic, but must admit that this got a good deal of looking at by me, even as I know that the car will not need anything as fancy as this, oil envy a terrible thing....

edit to add
http://www.millersoils.net/1_Millers_frame_MOTORSP...
a 15/60 specifically designed for use in large V8 (or so it says on their web site )
Edited by PRTVR on Wednesday 20th May 08:29
V8D Seem to prefer Valvoline Vr1 20/50. As they don’t sell it I can’t see they would specify it for any reason other than thinking it is the best choice. looking at discussions elsewhere on the web one of the arguments for this is it still has reasonable levels of an additive (ZDDP)specific to reducing cam wear which used to be in a fair a lot of main stream oils but has either been reduced or removed.
steve-V8s said:
V8D Seem to prefer Valvoline Vr1 20/50. As they don’t sell it I can’t see they would specify it for any reason other than thinking it is the best choice. looking at discussions elsewhere on the web one of the arguments for this is it still has reasonable levels of an additive (ZDDP)specific to reducing cam wear which used to be in a fair a lot of main stream oils but has either been reduced or removed.
I have had vr1 20/50 mineral in my engine for about 9 months now. Over the winter cold starts have been considerably rougher/noisier with this oil vs the mobil 1 I used to use. I am considered changing to a 10/50 synthteic or similar to improve cold starting - any views on this? Not really done a very cold start since using the VR1 so can’t t really comment on that. My current engine sounds a lot quieter in terms of valve gear noise than I remember when running the thinner Mobil 1 Motorsport but it is totally different cam followers and rockers. Personally I would rather have long lived cam lobes than worry about how fast it turns over when cold.
Have a tiny 17ah red top battery in mine by the way and I guess the coldest is has been at start up was about 8c and don’t recall any problem turning it over. In fact starting generally is now improved since I ran a nice thick cable directly from the battery to the block so that may be an unfair test.
Have a tiny 17ah red top battery in mine by the way and I guess the coldest is has been at start up was about 8c and don’t recall any problem turning it over. In fact starting generally is now improved since I ran a nice thick cable directly from the battery to the block so that may be an unfair test.
steve-V8s said:
Not really done a very cold start since using the VR1 so can’t t really comment on that. My current engine sounds a lot quieter in terms of valve gear noise than I remember when running the thinner Mobil 1 Motorsport but it is totally different cam followers and rockers. Personally I would rather have long lived cam lobes than worry about how fast it turns over when cold.
Have a tiny 17ah red top battery in mine by the way and I guess the coldest is has been at start up was about 8c and don’t recall any problem turning it over. In fact starting generally is now improved since I ran a nice thick cable directly from the battery to the block so that may be an unfair test.
Turns over fine - I just get a lot more tappet noise (I have hydraulic lifters) until she warms upHave a tiny 17ah red top battery in mine by the way and I guess the coldest is has been at start up was about 8c and don’t recall any problem turning it over. In fact starting generally is now improved since I ran a nice thick cable directly from the battery to the block so that may be an unfair test.
Me personally would not leave a mineral oil in one of these motors for 9 months,that could be the reason why you have noisy lifters on start-up, hydraulic lifters only function if they are clean once gum/varnish starts to build up you will have trouble shifting it unless you dismantle the lifter
minerals are more prone to this break down causing said problem
all IMHO.
minerals are more prone to this break down causing said problem
all IMHO.I think the acid test for any oil is if you see alarming pressure drops after 'exercising' the engine... I've tried some crappy brands of 'synths' with decent ratings/weights that couldn't even keep the oil pressure light down after some beans, and thats even with an oil cooler fitted 
Certainly the different TVR engines (and independent rebuilds I suppose) have different requirements. I believe some indies as a rule stick cooking oil in 400s and olive oil in 500s (so to speak) due to these differences?
At the end of the day you can easily end up wasting £40/50 on poor oil, that you change within 50 miles, is it worth the risk? The Mobil1 racing 15/50 and Silkolene ProR are well documented to cope with extreme heat & pressure encountered in TVR's. So unless you drive like a fairy its cheaper in the long run to use a quality oil IMHO.

Certainly the different TVR engines (and independent rebuilds I suppose) have different requirements. I believe some indies as a rule stick cooking oil in 400s and olive oil in 500s (so to speak) due to these differences?
At the end of the day you can easily end up wasting £40/50 on poor oil, that you change within 50 miles, is it worth the risk? The Mobil1 racing 15/50 and Silkolene ProR are well documented to cope with extreme heat & pressure encountered in TVR's. So unless you drive like a fairy its cheaper in the long run to use a quality oil IMHO.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff







