Measuring Fuel Pressure...
Measuring Fuel Pressure...
Author
Discussion

Al 450

Original Poster:

1,390 posts

252 months

Tuesday 19th May 2009
quotequote all
Hello all,

I suspect I'm overfuelling at idle before the ecu adapts and again in open loop running above 4000 rpm or so. I've been trying to measure the fuel pressure to check the regulator and fuel pump so I fitted an inline pressure gauge...

- With engine off but ignition on ( so the fuel pump runs briefly ) the system pressurises to a steady 39.5 psi then drops back to about 32.5 psi with the pump off. There's very little leakage after this.

- With engine idling and vac pipe disconnected from regulator the gauge is jumping around between 35 and 40 psi (should I have bought a damped gauge?) so it's impossible to get an accurate reading.

So is the fuel pressure too high? I think it might if the reading with the engine off is accurate.

And no I haven't got around to measuring Lambda voltage yet due to the pants weather (sorry Blitz) paperbag

blitzracing

6,422 posts

251 months

Tuesday 19th May 2009
quotequote all
The fuel pressure should not vary at all at idle with the vac pipe disconnected, and should be about 37 psi. If you think its engine vibration thats causing the problem, disconnect the fuel pump from the loom, and drive it from a separate 12 volt supply (a big battery charger will do OK) so you get a steady reading (Im assuming you can get at it??). You dont need to start the engine for this test. The ECU will cope with 40 PSI at idle and in closed loop, but it will cause a little overfueling in open loop, but not enough to blacken the plugs.

GreenV8S

31,028 posts

315 months

Tuesday 19th May 2009
quotequote all
Al 450 said:
- With engine idling and vac pipe disconnected from regulator the gauge is jumping around between 35 and 40 psi (should I have bought a damped gauge?) so it's impossible to get an accurate reading.
Yes.

Al 450

Original Poster:

1,390 posts

252 months

Tuesday 19th May 2009
quotequote all
GreenV8S said:
Al 450 said:
- With engine idling and vac pipe disconnected from regulator the gauge is jumping around between 35 and 40 psi (should I have bought a damped gauge?) so it's impossible to get an accurate reading.
Yes.
Bugger.

Al 450

Original Poster:

1,390 posts

252 months

Tuesday 19th May 2009
quotequote all
blitzracing said:
The fuel pressure should not vary at all at idle with the vac pipe disconnected, and should be about 37 psi. If you think its engine vibration thats causing the problem, disconnect the fuel pump from the loom, and drive it from a separate 12 volt supply (a big battery charger will do OK) so you get a steady reading (Im assuming you can get at it??). You dont need to start the engine for this test. The ECU will cope with 40 PSI at idle and in closed loop, but it will cause a little overfueling in open loop, but not enough to blacken the plugs.
I could plug a spare battery straight onto the fuel pump either at the pump connector or at the fuel pump relay in the footwell? However the pump runs for 3-4 seconds when the ignition is switched on and the 39.5 psi reading then is rock solid on the gauge.

I tried holding the gauge with the engine running but this made no difference so the pressure is definitely fluctuating, I just wasn't sure if this is normal or not. The gauge dial is not water filled though. Actually come to think of it the pressure was only fluctuating with the vac pipe disconnected. Maybe the reg is knackered... scratchchin

GreenV8S

31,028 posts

315 months

Tuesday 19th May 2009
quotequote all
Al 450 said:
blitzracing said:
The fuel pressure should not vary at all at idle with the vac pipe disconnected, and should be about 37 psi. If you think its engine vibration thats causing the problem, disconnect the fuel pump from the loom, and drive it from a separate 12 volt supply (a big battery charger will do OK) so you get a steady reading (Im assuming you can get at it??). You dont need to start the engine for this test. The ECU will cope with 40 PSI at idle and in closed loop, but it will cause a little overfueling in open loop, but not enough to blacken the plugs.
I could plug a spare battery straight onto the fuel pump either at the pump connector or at the fuel pump relay in the footwell? However the pump runs for 3-4 seconds when the ignition is switched on and the 39.5 psi reading then is rock solid on the gauge.

I tried holding the gauge with the engine running but this made no difference so the pressure is definitely fluctuating, I just wasn't sure if this is normal or not. The gauge dial is not water filled though. Actually come to think of it the pressure was only fluctuating with the vac pipe disconnected. Maybe the reg is knackered... scratchchin
With the engine running the fuel rail pressure spikes all over the place. You need a damped gauge to get a sensible average reading.