Some Utter %#*t
Discussion
The above mentioned has tried to break in to my car. Hopefully only an attempt to nick stuff out of the recesses - there wasnt any stuff in them except my A-to-Z & a road atlas, which were spared - presumably as you can't hawk them off for either heroin or plasma TVs to watch Jeremy Kyle on.
Unfortunately in the process this likely-inbred scumbag has torn the roof material away from the moving roof arch and ripped a good length of the stitching in the ribbing along the bottom. Have not had a proper chance to survey the damage yet as had to go to work - hopefully it's not more extensive than this though.
With the only stitching I've ever done being in the construction of a tie-dye cushion in high school I'm thinking this is probably a job best left to the pros.
Can anyone recommend a decent roofing person/company within a hoon of SW London?
Also what glue is it that sticks the roof to the arch?
Cheers again guys...
Grr.
Unfortunately in the process this likely-inbred scumbag has torn the roof material away from the moving roof arch and ripped a good length of the stitching in the ribbing along the bottom. Have not had a proper chance to survey the damage yet as had to go to work - hopefully it's not more extensive than this though.
With the only stitching I've ever done being in the construction of a tie-dye cushion in high school I'm thinking this is probably a job best left to the pros.
Can anyone recommend a decent roofing person/company within a hoon of SW London?
Also what glue is it that sticks the roof to the arch?
Cheers again guys...
Grr.
Im assuming tosser pulled the hood up where it meets the deck by the window ie where it has the velcro............... not much help im afraid but a couple of spring loaded rat traps could be fun in that area, just remember yourself, however you prob get nicked if the chav hurt himself while in ur car
I'm in the process of fitting a new hood to mine. Mine had a similar tale to yours before I got it. Said scrote knifed the rear window to get in and wrecked the radio console getting the radio out.
I've had to rebuild the radio mounting structure which was all smashed up. But that's a story on it's own.
However, back to the hood. Well, the previous owner had got it repaired. Think it must have been David Blunkett Hood Repairers Ltd, because it was refitted skew-whiff, about inch and half long on one side and consequently the same but short on t'other side.Which of course meant that it easily took in water. However, being glued it could not be straightened out. (Bear with me, I'm getting there!!!)
So, the glue used on mine was obviously Evo-Stik or something very similar.It was a complete t**t to get off the tension ring and the targa, would not have liked to try to remove it from the hood had I been re-using it.
I am fitting a completely new hood. Not too difficult an operation if you are at all handy.
If you need any more on it give me a shout.(What was the first question????)
HTH
Phil
I've had to rebuild the radio mounting structure which was all smashed up. But that's a story on it's own.
However, back to the hood. Well, the previous owner had got it repaired. Think it must have been David Blunkett Hood Repairers Ltd, because it was refitted skew-whiff, about inch and half long on one side and consequently the same but short on t'other side.Which of course meant that it easily took in water. However, being glued it could not be straightened out. (Bear with me, I'm getting there!!!)
So, the glue used on mine was obviously Evo-Stik or something very similar.It was a complete t**t to get off the tension ring and the targa, would not have liked to try to remove it from the hood had I been re-using it.
I am fitting a completely new hood. Not too difficult an operation if you are at all handy.
If you need any more on it give me a shout.(What was the first question????)
HTH
Phil
Sticking Stanley knife blades into a position that a thief might cut themselves is very naughty and you shouldn’t do it.
If you ever look under the edge of a ‘hardened’ (armour plated limo type) car, you may find special clamp brackets. These hold a continuous row of Stanley blades under the sills.
Angry crowds may be tempted to try overturning cars by grabbing the car under the sills.
Our politicians may get away with this, but you won’t, so please refrain from doing it.
If you ever look under the edge of a ‘hardened’ (armour plated limo type) car, you may find special clamp brackets. These hold a continuous row of Stanley blades under the sills.
Angry crowds may be tempted to try overturning cars by grabbing the car under the sills.
Our politicians may get away with this, but you won’t, so please refrain from doing it.
As long as the *&%* didn't tear the fabric itself you'd be able to glue the fabric back to the targa hoop quite successfully with some contact adhesive like I did.
I also repaired the stiching that had rotted around the velcro myself with an awl I bought off ebay and some waxed thread from HobbyCraft or wherever and while it's not as good as a professional job I'm quite please with it.
My sewing skills were also restricted to previously sewing a button on my shirt.
I also repaired the stiching that had rotted around the velcro myself with an awl I bought off ebay and some waxed thread from HobbyCraft or wherever and while it's not as good as a professional job I'm quite please with it.
My sewing skills were also restricted to previously sewing a button on my shirt.
Uncle Fester said:
Sticking Stanley knife blades into a position that a thief might cut themselves is very naughty and you shouldn’t do it.
If you ever look under the edge of a ‘hardened’ (armour plated limo type) car, you may find special clamp brackets. These hold a continuous row of Stanley blades under the sills.
Angry crowds may be tempted to try overturning cars by grabbing the car under the sills.
Our politicians may get away with this, but you won’t, so please refrain from doing it.
If you ever look under the edge of a ‘hardened’ (armour plated limo type) car, you may find special clamp brackets. These hold a continuous row of Stanley blades under the sills.
Angry crowds may be tempted to try overturning cars by grabbing the car under the sills.
Our politicians may get away with this, but you won’t, so please refrain from doing it.




Cheers guys. Some useful advice there
. Has indeed been pulled up at the velcroed corner. Reckon the arch-fixed bit recoverable but am having to wait to do a proper damage check. To my suprise when I reported it to Old Bill they were quite good and are meant to be coming round tonight to 'forensicate' (their word) my car & garage gates.
Have bought a roll of duck tape to seal it up for my weekend away...
While I wait I'm trying to devise a method to electrify a row of razor blades...
. Has indeed been pulled up at the velcroed corner. Reckon the arch-fixed bit recoverable but am having to wait to do a proper damage check. To my suprise when I reported it to Old Bill they were quite good and are meant to be coming round tonight to 'forensicate' (their word) my car & garage gates.Have bought a roll of duck tape to seal it up for my weekend away...
While I wait I'm trying to devise a method to electrify a row of razor blades...
http://www.youtube.com/watch?v=fDrzMGdYWZc
probably better to use this when the car is on your drive rather than in the street though!!!
probably better to use this when the car is on your drive rather than in the street though!!!
I had my roof repaired by a local bloke - Cambridge - that I found in Yellow Pages. I think it was under Coachbuilders.
Alternatively, you could ask your local dealer who they use as they're unlikely to do it themselves onsite.
This should not be very expensive - I had the rear section taken off, new plastic window put in, and re-mounted for about £250, from memory.
I had a whole new roof for my MX5 from the same bloke - £650 for Mohair.
Rick
Alternatively, you could ask your local dealer who they use as they're unlikely to do it themselves onsite.
This should not be very expensive - I had the rear section taken off, new plastic window put in, and re-mounted for about £250, from memory.
I had a whole new roof for my MX5 from the same bloke - £650 for Mohair.
Rick
Cheers.
Had a proper look at the damage. Luckily seems quite localised. Re-stich to the skirt that holds the roof down (not sure if this needs to be seperated from the car to gain access?) and reglue of both sides - yes the git did both sides
. No major damage to the material though thankfully.
I'm due a service so I will see what the garage/their people quote as just want it back in full working order having spent a while recently sorting niggles.
Old bill didn't turn up in the end... sigh.
Had a proper look at the damage. Luckily seems quite localised. Re-stich to the skirt that holds the roof down (not sure if this needs to be seperated from the car to gain access?) and reglue of both sides - yes the git did both sides
. No major damage to the material though thankfully.I'm due a service so I will see what the garage/their people quote as just want it back in full working order having spent a while recently sorting niggles.
Old bill didn't turn up in the end... sigh.
Sorry to hear about your damage, hope you get her sorted. It's the mentality of these thugs. Half the time they get away with less than £100 of stuff (black market prices) yet they don't think twice about defacing someones classic car and causing maybe £000's of damage for their ill gotten gains.
It always interests me when such people are asked what they think/would do to some one who breaks into their home or car. It's usually a very different story then.
It always interests me when such people are asked what they think/would do to some one who breaks into their home or car. It's usually a very different story then.

Gassing Station | Chimaera | Top of Page | What's New | My Stuff




king little b