Rapid protoyping - moulding - working prototype
Rapid protoyping - moulding - working prototype
Author
Discussion

0191mark

Original Poster:

6,087 posts

207 months

Thursday 20th August 2009
quotequote all
*mods, could you amend the spacing on the thread title please?

Hello all, my first post relates to some R&D I'm about to embark on. Seeing as I'm at the 'pre-start-up-business-stage' I thought this might be a good place to get started here on PH.

Rapid Prototyping>mould>working prototype.

I want to get an idea of what sort of R&D costs I may incur if I take a design to the working prototype (PT) stage. What I want to be able to do is set up the PT in a testing environment as well as in a longer term evaluation environment. At this stage the design isn't fully protected so I can't go into a huge amount of detail - but the item in question is fairly simple.

A (white?) hollow plastic cube (four walls) with a moulded internal 'brace' half way between the base and the top and bottom opening.

Approx 8" square/perhaps trapezoid. Walls perhaps 3mm thick, quantity x 150.

Can anyone give me a rough idea of the cost of having 150 of these units produced (in the UK) for PT/demonstration purposes? The exact dimensions haven't been determined, neither have any other specs other than the approx. size, colour and mid way brace. Obviously there will be some CAD and 3D rendering to do as part of this process - so what sort of rough figure would you expect to charge or pay to have this project researched and developed to a working PT stage?

Mark


Edited by 0191mark on Thursday 20th August 15:13

dudleybloke

20,553 posts

217 months

Thursday 20th August 2009
quotequote all
would it have to be moulded?
for early prototypes you could probably glue pieces together to make the part.

EINSIGN

5,638 posts

277 months

Thursday 20th August 2009
quotequote all
I have used these guys before: http://www.zcorp.com/en/home.aspx

This 3D printing technology is advancing fast and is really impressive. This is a powder/resin based process which means the end result isn’t useable in most cases. There are services offering laser/liquid prototyping in different materials.

Give it a few more years and you will be printing off your product purchases and dinner at home…

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
dudleybloke said:
would it have to be moulded?
for early prototypes you could probably glue pieces together to make the part.
I need a few (150) so my thinking is to get an estimate on a moulding and a short run.

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
EINSIGN said:
I have used these guys before: http://www.zcorp.com/en/home.aspx

This 3D printing technology is advancing fast and is really impressive. This is a powder/resin based process which means the end result isn’t useable in most cases. There are services offering laser/liquid prototyping in different materials.

Give it a few more years and you will be printing off your product purchases and dinner at home…
Thanks for that, I'll have a look - just got a surprisingly good quote from a Newcastle Uni associated business for an RP only. Now I just need to determine the cost of a mould and a short run elsewhere - but will definitely look at zcorp as you suggest.

DB81

44 posts

286 months

Friday 21st August 2009
quotequote all
Hi Mark,

A bit of a plug (my ex works for the company) but contact http://www.thompsonprecision.co.uk/design_services... as they often deal with RP and might be able to help you out.

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
DB81 said:
Hi Mark,

A bit of a plug (my ex works for the company) but contact http://www.thompsonprecision.co.uk/design_services... as they often deal with RP and might be able to help you out.
I'll definitely take a look - thanks for the pointer.

xllifts

3,724 posts

234 months

Friday 21st August 2009
quotequote all
This maybe of no use to you at all, but a few years back i wanted to prototype a plastic L shaped bracket with a slot through the middle to enable full adjustment, any way i digress... this was 225mm x 3mm x 60mm on each leg if that makes sense.

I visited several injection moulding co's and small tooling co's and they all came back with a figure of 5k just for the tooling to mould the PT

As said before is this something that could be liquid poured into plasticine/clay mould ?

dudleybloke

20,553 posts

217 months

Friday 21st August 2009
quotequote all
i would leave whe moulding untill you have all your dimensions decided on.

150 pieces sounds like a lot to do by hand but it wont take too long.
tooling up is expensive and you dont want to keep getting moulds made for every small alteration you might do.
injection tooling is extremely expensive and something like what you want could cost several thousand pounds if you want it moulded in one piece.

dudleybloke

20,553 posts

217 months

Friday 21st August 2009
quotequote all
you might be able to get an extrusion that will match the dimensions and then simply glue/bond the internal brace in situ.

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
xllifts said:
This maybe of no use to you at all, but a few years back i wanted to prototype a plastic L shaped bracket with a slot through the middle to enable full adjustment, any way i digress... this was 225mm x 3mm x 60mm on each leg if that makes sense.

I visited several injection moulding co's and small tooling co's and they all came back with a figure of 5k just for the tooling to mould the PT

As said before is this something that could be liquid poured into plasticine/clay mould ?
I was hoping someone might be able to advise TBH, as I don't have any idea which process might be most suitable taking in to account dimensions, thickness, format etc. But your quote at least gives me some sort of figure to start from - thanks for that.


dudleybloke

20,553 posts

217 months

Friday 21st August 2009
quotequote all
i would seriously look at extrusions to do this.
for what you want an injection mould would have to be a complex multi part job which could easyly cost more than 30k.
an extrusion tool for the box section would probably be less than 6k depending on the required finish.
cut extrusion to length then glue brace inside using a simple jig to locate.

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
dudleybloke said:
you might be able to get an extrusion that will match the dimensions and then simply glue/bond the internal brace in situ.
I understand a hollow cube could be extruded (4 parallel faces) - but the shape I'm likely to need will be approx 8x8x8" shape, but with the top opening being about 6 1/2" x 61/2". That is, the four faces will need to slant in towards each other slightly. Is it possible to extrude something like this?

dudleybloke

20,553 posts

217 months

Friday 21st August 2009
quotequote all
could you knock a quick sketch up. it doesnt have to be brilliant.
pm me if you want.

0191mark

Original Poster:

6,087 posts

207 months

Friday 21st August 2009
quotequote all
dudleybloke said:
could you knock a quick sketch up. it doesnt have to be brilliant.
pm me if you want.
The PC I'm using at the minute has no illustration software on it but I'll be on my mac next week - PM you then - thanks!

justinbaker

1,339 posts

279 months

Saturday 29th August 2009
quotequote all
Mark Hi,

If you send me a sketch I will produce you a 3D model. Drawing - Free of charge if it helps.

JB